Filter Results By:

Products

Applications

Manufacturers

Meters

sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.

See Also: Sensors, Measurement


Showing recent results 3826 - 3840 of 4301 products found.

  • Automatic Ratio Testers

    TTR-3D Series - Amperis sl

    The TTR-3D of ratio meters are high precision instruments, designed to measure turn ratios, phase displacements, excitation currents of single phase and three phase power, distribution and instrument transformers in conformity to the IEEE C57.12.90 & IEC 60076

  • Electrical Circuit / Wire Harness Analyzer

    ECAD System 2005 - CM Technologies Inc.

    The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.

  • HSI Test Fixture

    TA-552 - Tech-Aid Products

    This test fixture provides the necessary panel controls, switching and cable pin-outs required to test the KPI-552/KPI-553/A series of HSI's as described in their respective maintenance manuals. This fixture will serve as the "Instrument Bench Tester" and does have the required differential resolvers and relay switching. Panel jacks are provided for the Heading, Course, RMI and ADF synchro sources that are external to this fixture. The use of external synchro sources serves to minimize the cost of this panel. Additional items incorporated on the panel are test jacks to monitor the meter drive voltage and current as well as a momentary switch to open the meter drive and this serves to verify sticky meter stops. The fixtures rear panel provides for all power inputs as well as an I/O connector if the shop desires to interface an external synchro panel.

  • Turnkey Solution for Unattended Noise Monitoring

    NoiseScout - NTi Audio AG

    NoiseScout provides a comprehensive but easy-to-use 24/7 noise monitoring solution. Noise levels are recorded on-site by the XL2 Sound Level Meter and are available online for monitoring and download. NoiseScout is aimed at both short term noise assessments and long term monitoring applications. During acquisition, automated email alerts allow noise issues to be addressed before a non-compliance condition arises. NoiseScout displays the noise levels measured by the XL2 Sound Level Meter live in your web browser. The measurement data recorded out in the field is presented online in charts and dashboards. Multiple noise level meters can be monitored simultaneously within the map view, thus providing localized geographic visualization for all noise levels at a glance. Identified users can access all their projects, control their monitors or create basic view modes, allowing stakeholders to oversee their noise level data.

  • Tunable Laser Source, Low SSE, Value Line

    81607A - Keysight Technologies

    The new Keysight 8160xA tunable laser sources are based on a common cavity and laser module design. They share a narrow line width and a low spontaneous emission level that, in combination with the Keysight N774xA multiport power meters, or the Keysight 816xxx power meter modules, enables excellent spectral loss measurement ranges in both stop band and pass band. A built-in gas cell and self-adjustment capabilities ensure excellent long-term stability to minimize cost of ownership. Within the 8160xA family, the Value Line and Basic Line models offer additional price-performance options based on output power, tuning modes and speed, wavelength accuracy and repeatability.

  • Tunable Laser Source, High Power and Low SSE, Value Line

    81608A - Keysight Technologies

    The new Keysight 8160xA tunable laser sources are based on a common cavity and laser module design. They share a narrow line width and a low spontaneous emission level that, in combination with the Keysight N774xA multiport power meters, or the Keysight 816xxx power meter modules, enables excellent spectral loss measurement ranges in both stop band and pass band. A built-in gas cell and self-adjustment capabilities ensure excellent long-term stability to minimize cost of ownership. Within the 8160xA family, the value and basic line models offer additional price-performance options based on output power, tuning modes and speed, wavelength accuracy and repeatability.

  • Programmable Ammeter

    IM1953 - Ajinkya Electronic Systems

    An ammeter is a measuring instrument used to measure the electric current in a circuit. The majority of ammeters are either connected in series with the circuit carrying the current to be measured or have their shunt resistors connected similarly in series. We manufacture Programmable Ammeters, which are DC current indicators with High and Low alarm limits. These ammeters are acknowledged for their smooth functioning, reliability and high efficiency. Moreover, these are available with various features like peak hold, retransmission output, MODBUS serial PC Interface. Other models available are: Ampere hour meters / Watt meters / Current Voltage loggers etc.

  • Test Equipment

    Southern Photonics Ltd

    Southern Photonics designed and manufactured all the test equipment currently being manufactured by Coherent Solutions, as well as equipment for non-telecoms applications. This includes FBG strain interrogators, optical pulse phase analysers, OSNR meters, optical power meters, optical spectrum analysers, optical gas sensors… you get the idea. All test equipment we build is robust and easy to use. The picture shows some of what we can do – anything from prototype benchtop test gear (as in the combination ASE source and laser combiner on top of the stack) to field test equipment (the portable fast OSA on the bottom).

  • Power Cell Power Transducers for Wide Ranging AC/DC Loads

    PH-3A and PH-1000 - Powertek LLC

    You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.

  • Step-Tunable Laser Source, High Power and Low SSE, Basic Line

    81609A - Keysight Technologies

    The new Keysight 8160xA tunable laser sources are based on a common cavity and laser module design. They share a narrow line width and a low spontaneous emission level that, in combination with the Keysight N774xA multiport power meters, or the Keysight 816xxx power meter modules, enables excellent spectral loss measurement ranges in both stop band and pass band. A built-in gas cell and self-adjustment capabilities ensure excellent long-term stability to minimize cost of ownership. Within the 8160xA family, the value and basic line models offer additional price-performance options based on output power, tuning modes and speed, wavelength accuracy and repeatability.

  • Fiber Optic Light Source

    Huihong Fiber Inc

    Fiber optic light source is a fiber optic test equipment to measure the fiber optic loss for both single mode fiber cable and multimode fiber cables; usually the fiber optic light source is used with the fiber optic power meters. This fiber optical light source can provide wavelength output according to the specific requirements including the 650nm red source, 1310nm/1550nm wavelength for the single mode fiber and 850nm/1300nm wavelength for the multimode fiber. Used together with our fiber optic power meter, they act as an economic and efficient solution for the fiber optic network works.

  • Resistance Measurement

    KoCoS Messtechnik AG

    PROMET 100 / 200 / 600 high-accuracy, precision ohm meters deliver an adjustable test current up to 600 A which is independent of the supply voltage. They utilize the four-wire resistance measurement method, enabling them to meet extremely stringent accuracy requirements when determining resistance values in the micro-ohm range.State-of-the-art power electronics coupled with a robust design guarantee maximum reliability, even when used as portable devices in switching stations or industrial environments.The modern operating concept, an interface to the test systems of the ACTAS product line and an optional remote control unit make these micro-ohm meters flexible and versatile.

  • Digital Protective Relay Test Set

    K1066+ - KINGSINE Electric Automation Co., Ltd.

    1. Adopts 6.4 large LCD screen, and provided with VGA video interface, making it available to connect to projector for training;2. With alarm function of housing grounding testing and external voltage input, to guaranty personal security;3. Offer independent Aux. DC to tested devices, 0 ~ 300V/0.6A(Poleless and adjustable);4. Two in one of meter and source, with function of both internal and external testing, self-calibration, oscillograph, and the duration of each oscillograph reaches 50S (optional function);5. Function of transducer and energy meter testing (optional function);

  • High Performance Polyphase Energy Metering AFE w/ Power Quality Analysis

    ADE9000 - Analog Devices Inc.

    The ADE9000 is a highly accurate, fully integrated energy-metering device. Interfacing with both current transformer (CT) and Rogowski coil sensors, the ADE9000 enables users to develop a three-phase metrology platform, which achieves high performance for Class 1 through Class 0.2 meters. Power quality features enable advanced meter designs with fast rms measurements and power quality level monitoring for EN50160 compliance. The ADE9000 integrates seven high performances ADC’s, a flexible DSP core. An integrated high-end reference ensures low drift over temperature with a combined drift of less than ±25 ppm/°C max for the whole channel including PGA and ADC.

  • Hand-Held Field Testing Device

    3 SERIES - Powermetrix Systems

    Powermetrix is pleased to introduce a revolutionary hand-held field testing device for the electric utility industry. The PowerMaster 3 Series is an ultra-compact field instrument with a true 3-phase analyzing reference standard that performs various metering site accuracy tests. This analyzer operates under actual customer load conditions so a true representation of site accuracy can be verified. Meter Testing, CT/PT ratio testing, CT/PT burden measurement, meter register/demand testing and wiring verification are all easily performed with this extremely portable, hand-held analyzer. With many advanced features, this new pint-sized analyzer is revolutionizing field testing as we know it.