Filter Results By:

Products

Applications

Manufacturers

Meters

sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.

See Also: Sensors, Measurement


Showing recent results 3946 - 3960 of 4219 products found.

  • HIGH FREQUENCY DC BIAS

    6565 SERIES - Wayne Kerr Electronics, Ltd.

    The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.

  • ETHERNET COPPER EXTENDER FOR 10/100 NETWORKS, VDSL2

    EIR2-EXTEND - B+B SmartWorx

    Hardened 10/100BSE-TX Ethernet ExtenderExtend Ethernet Copper up to 2200 meters (7218 feet) over existing copper wire (common copper, telephone, Cat5e)VDSL2 technology with transmission rate of 100Mbps at 400meters-40°C to 75°C (-40°F to 167°F) operating temperature rangeAuto -detection of Local/Remote function to reduce installation timeLocal/Remote function to reduce installation timeLink-Down-Relay (LDR) function to inform link loss to other sideOne 10/100Base TX (TX) Ethernet port with RJ-45 connectorIEEE 802.3 10BaseT and IEEE 802.3u 100BaseTX compliantLine port uses common RJ-11 connector

  • Fluxmeter

    Model 2130 - Magnetic Instrumentation Inc.

    The Model 2130 Fluxmeter is a fully featured, high-end Fluxmeter based measurement system. It is a compact instrument with high accuracy, automatic drift correction, microprocessor control, and twelve measurement ranges to allow the operator to configure the meter for maximum resolution and accuracy. The Model 2130 is capable of measuring (DC), alternating (AC), or pulsed magnetic fields. Selecting primary measurement functions is quick and easy with dedicated front panel function keys. An easy to use menu allows access to user defined parameters such as upper and lower magnetic limits and relative magnetic measurements.

  • Free chlorine Handy Photometer

    MW10 - Milwaukee Instruments

    The revolutionary new range of Milwaukee handy photometers are compact and easy to use, have a modern design, and measure Free Chlorine (MW10); Total Chlorine (MW11); Phosphate (MW12); Iodine (MW13) and Iron (MW14). Their main advantages are the small size, and the real simplicity when doing measurements on the spot. Within a few minutes you can get the required result on the LCD and the instrument directly displays the concentration of the specific component in ppm. The meter automatically turns off after 2 minutes in order to save the battery.They work exactly the same way as the other Milwaukee photometers:

  • Energized Cable Sensor

    Hubbell Power Systems Inc

    The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.

  • Energy Data Concentrators

    Advantech Co. Ltd.

    Advantech''s provides a series of high quality Energy Data Concentrators and Power meters to strengthen building automation system. Our Energy Data Concentrator supports serial communication ports and several networking interfaces. In addition, pre-installed with Advantech''s WinCE WebAccess management software, the Energy Data Concentrator is browser-controlled, whose Web Server function increases flexibility and convenience, making it easy to configure and maintain the building automation system via the Internet. With a built-in driver, the powerful data concentrators BEMG-4110/4220 can make multi-thread communication and collect data from a wide variety of building automation system equipment and devices.

  • ENERGY MANAGEMENT SYSTEM (EMS)

    Nippen Electrical Instruments Co.

    Smart Analyser - Total Energy Management Solution is available in three flavors as follows:A) Standard version ships with the basic required facilities such as Online Monitoring of Real Time data, Graphical Representation of Current Values, Tabular format of historical data, Alarms at a particular level crossed. It can export the data to the other spreadsheet utitilies. In the settings option you can set the parameters for the Alarms, Meter selection, ranges. The software is armed with easy help at each stage of usage.B) Professional Version contains above & some advanced features such as zooming the Graphs for better Precision. It will e-mail the alarmed data periodically to a particular Email ID. It generates Tariff Bills report as per settings.

  • Wireless High-voltage Phasing Tester

    TAG-8000 - Wuhan Nanrui Electric Co,. Ltd

    TAG-8000 Wireless High-voltage Phasing Tester , used in power lines , substations and phase sequence phase checksum verification , with nuclear phase , phase sequence , electrical inspection and other functions with a strong anti-interference, compliance (EMC ) standards, adapt to various electromagnetic interference occasions . High voltage phase signal will be measured by the collector out emitted directly after the treatment . Received by the nuclear phase and the phase comparison , the results for the nuclear phase characterization. Because TAG-8000 Wireless high-pressure nuclear phase meter is a wireless transmission , thereby achieving safe, reliable, fast and accurate , adapt to various nuclear phase occasion.

  • High Voltage EMC Surge Generator

    TM510 - T&M Tools Limited Co

    TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.

  • Undersea Positioning System

    LBL Series - Teledyne Benthos

    ​​​Undersea Positioning requires an appropriate integrated system composed of at least two components but often more. Teledyne Benthos offers a full line of positioning products that can be configured in many different ways. Long Baseline (LBL)A collection of fixed, and potentially mobile, transponders can be used to calculate range between any one node and the others. The distance between the transponders is usually hundreds, if not thousands, of meters- hence long baseline. With the inclusion of telemetry, a network can adapt to changing transponder positions to provide greater operational flexibility. LBL systems offer the highest accuracy potential but can be complex to deploy. The telemetry built into Teledyne Benthos positioning products can minimize, though not entirely eliminate, this challenge.

  • Digital Multimeter

    6420 DM - Standard Electric Works Co., Ltd

    ● 4000 counts LCD with a maximum display of 3999.● Angled display design helps the user to identify the reading of value   easier.● Auto ranging designed.● Bar graph LCD display.● Range change function.● Relative/Maximum/Minimum modes.● Peak hold mode.● VAHz mode measures frequency in voltage or current mode.● 40M Hz frequency counter.● Auto Power off.● Continuity check.● Data hold function.● Low battery indication.● Over range indication.● Fuse protection.● Special hook design used to hang the meter for ease of use.

  • ELECTRICAL TEST Kit

    1021 TK - Standard Electric Works Co., Ltd

    2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.

  • Wide Angle Scale Instrument

    LS-96 - Standard Electric Works Co., Ltd

    ● For ranges higher than 20A DC, use external shunt with a 50mV DC Ammeter.● For ranges higher than 300V DC, use external Volt Divider with a 1mA Voltmeter.● For ranges higher than 5A AC, use external Current Transformer with a 5A AC Ammeter. ● For ranges higher than 600V AC, use external Potential Transformer with a 150V AC Voltmeter.● Full Scale Deflection : 250° ● Accuracy : Class 1.5● Composition : Glass window, ABS resin frame and case, -PC glass fiber base mounting fittings included.● Color : Black base and frame, white scale plate and meter body.● Pointer : Stick shape in black color.

  • RFID Tags

    GAO Tek Inc.

    RFID tags bring the future of technology to today. Radio-frequency Identification(RFID) tags can be placed on almost any piece of clothing, cash, animals and even humans. Tags use electromagnetic fields to identify and track the desired object. Active tags are powered by a battery located inside the tag, and may operate over hundreds of meters away from the RFID reader. RFID tags have been expanding ever since their inception – they became especially popular when used in toll readers and assembly lines to track the product’s progress throughout the assembly line.

  • Pressure Sensors

    ESI Technology Ltd

    ESI Technology manufacture a wide range of pressure sensors using a variety of different technologies. Pressure transducers (voltage output), pressure transmitters (milliamp output), panel meters, accessories. Silicon-on-Sapphire technology and a titanium diaphragm combine to make the new Gold Standard in pressure sensing. Custom pressure measurement solutions have been integral to ESI’s success. All aspects of design and manufacture are done in-house at our UK facility. Impressive quality at an affordable price. So if you don’t see what you are looking for, just ask.