Filter Results By:

Products

Applications

Manufacturers

Meters

sense, display, measures; gas, water, electricity, particles, vibration, light or quanta.

See Also: Sensors, Measurement


Showing recent results 4156 - 4170 of 4302 products found.

  • Sound Level Calibrator

    CRY5611 - Hangzhou JiGao Electroacoustical Science and Technology Co.,Ltd

    CRY5611 Sound Level Calibrator is suit for the sound pressure calibration of sound level meter and electroacoustic tester. CRY5611 has the merit of high stability, small, light weight, low power and facility of using. Its Work frequency is 1000Hz, it has no relationship with the weighting network when be calibrated. (Attenuation of weighting network of A,B,C,D, is zero, at 1000Hz).

  • 0.3Hz-3MHz Amplitude Display Functional Generator

    MFG-8303 - MCH Instruments Co.,Ltd.

    Features:*Max. frequency up to 15MHz*Single-chip function generating module provides high stability and low distortion waveforms*5 digit frequency display, 3 digit amplitude display.*Built-in frequency meter for testing external signal up to 20MHz*Linear and Logarithmic sweep function.*AM/FM function optional(Models with suffix “A”)*5W Power Output function optional(Models with suffix “W”)

  • Phasing Voltmeter/Sensor (2 in 1)

    STB Electrical Test Equipment, Inc

    STB unit replaces 3 separate units manufactured by competitors - line phasing, capacitance phasing and line to ground Versatile, lightweight and easy to useEach portable meter has a single rangeMeter usage: Voltage detection and phasing at capacitance test points or voltage detection and phasing on bare energized conductors (overhead & underground)Probes can be separated to be used as a voltage sensor or capacitance sensorFive position selector switch used to select voltage sensing on capacitance tap or direct line and phasing on capacitance tap, direct line or a battery test positionNo exposed conducting terminals or meter circuitryLocking cable connector provides positive contactScale is large enough to be easily read 8'-10' when mounted on a suitable hot stickLine to ground voltage readings are accurate within 3% at full scaleMaximum operating temperature range -20°F to 165°F (-30°C to 75°C)25' coiled cable includedAccessoriesMODELDESCRIPTION50118-G-10Hot Sticks (full set - 6)10104-P-02Shepherd's Hook10104-P-03Probe Tip30142-P-01Shot Gun Adapter50111-P-01Regular Bushing Adapter10275-P-01Universal AdapterModelsMODELDESCRIPTIONWeight50101-G-07Phasing Voltmeter 9-36kV16 lbs.50101-G-08Phasing Voltmeter 9-36kV with Hot Sticks (full set - 6)21 lbs.Request QuoteOperating Instructions9-36kV Phasing VoltmeterProduct Summary/OptionsProvides safe and convenient testing means for paralleling 3-phase high voltage circuitsConsists of two resistance elements connected in series with an indicating meter in the series connectionTwo ranges, 9kV and 36kV, with a range selector switch mounted on the back of the meter housingSwitch is clearly marked for the range of the voltmeterTypical use: Line-to-ground voltage measurements and phase for paralelling operationsScale markings on the voltmeter have a minimum of divisions and the figures are large enough to be easily read 8'-10' away when mounted on a suitable hot stickInput impedance: Approximately 72 megohmsMaximum operating temperature range -20°F to 165°F (-30°C to 75°C)Ready to attach on hot stick10' cable, a proof tester, battery and shepherd’s hook and probe tip includedOperating InstructionsRequest QuoteOperating InstructionsModelsMODELDESCRIPTION50100-G-010-2kV DC Voltmeter 30’ cable, magnetic track adapter50100-G-020-1500kV DC Voltage Meter50100-G-030-1500kV DC Voltage Meter with Hot Sticks50100-G-04DC Voltmeter 1500kV DC w/Extension Probe and Ground Lead50100-G-050-1500V DC with Hot Sticks and Lighted Dial50100-G-060-1500 DC Voltage Meter with Lighted DialDC Voltmeter​Product Summary/OptionsLightweight, easy to use, hand-held meterHard wired unit Scaled 0-1500vDC, in 100 volt incrementsProvides a 2/3 full scale deflection when applied across 1000vDCMaximum current flow through instrument at 1000vDC is 0.05 milliampersNo polarity, sensitivity issuesMay be used to determine whether the third rail of a transit system is energizedInput impedance of approximately 24 megohmMaximum operating temperature range -20°F to 165°F (-30° C to 75°C) Request QuoteAC VoltmeterProduct Summary/OptionsTwo-position toggle switchPortable instrument for quickly and easily measuring AC voltages Locking cable connector provides positive, electrical contactResistive voltmeter - medium range voltage measurements in the fieldTypical use - measure voltage between ground and the line or bus connector20' ground lead includedInput impedance - approximately 36 meghomsMaximum operating temperature rangeAccuracy of +/- 3% full scaleShare to TwitterShare to FacebookShare to PrintShare to EmailMore AddThis Share options

  • Seismic Sensor

    D7S - Omron Electronic Components

    Specifically designed for the growing number of autonomous IoT systems, the Omron D7S provides high precision measurement of spectral intensity, allowing it to reject impulse vibration noise and only respond to genuine seismic activity. Despite its compact size, D7S features its own internal memory and I2C interface, allowing it to be readily integrated into IoT devices. Potential applications include smart electricity and gas meters, wireless sensors, industrial control panels, electricity distribution panels, fire-prevention systems, home appliances such as heaters and gas stoves, chemical plants, expressways, bridges, tunnels, roads and many more. Commenting, Fabrizio Petris, Senior Business Development Manager of Omron Electronic Components Europe said, “Earthquakes are extremely common around the world. On average, 50 earthquakes strike each day, or about 20,000 a year. Many are weak enough to go unnoticed but some are catastrophic. We can’t always predict when a catastrophe will strike. Using the new sensor from Omron, designers can make systems safer and minimise the risk of secondary damage after earthquakes by safely shutting off and stopping hazardous devices. The sensor can also help determine damage by mapping seismic intensity and providing building collapse information.”

  • High Bandwidth CoaXPress Camera

    Bonito PRO CoaXPress - Allied Vision Technologies

    Allied Vision introduces a new camera family and enters the high-speed camera market: The Bonito PRO CoaXPress camera is perfectly suited for high-bandwidth applications. It will be presented to the public for the first time at the Image Sensing Show in Yokohama, Japan, from June 7 to June 9, 2017 (at the booth of Allied Vision distribution partner AproLink Corporation, Booth no. 63). Allied Vision’s new high-bandwidth camera series is equipped with 4 x CXP-6 ports enabling bit rates of 25 Gbit/s over four coaxial cables with a maximum communication distance of 68 meters. The first two Bonito PRO series models support the latest high-resolution ON Semi PYTHON CMOS sensors with 26.2 Megapixel and 12.5 Megapixel resolutions. Customers can choose between monochrome and color sensors, as well as an NIR sensor option with enhanced near infrared sensitivity. The combination of ON Semi PYTHON CMOS sensors with the Bonito PRO’s rugged, fan-less housing design, and its comprehensive feature set make these cameras an ideal choice for high-definition imaging applications demanding high throughput, robustness, and design-in flexibility.

  • Vector/Magnitude Gaussmeter

    VGM - Alpha Lab, Inc.

    The Vector Gaussmeter displays the true magnitude of the field at any location as well as the X, Y, Z components of up to 800 gauss. Also separately displays peak values of X, Y, Z, and magnitude. There is a sound alarm that determines the locations where the field magnitude exceeds user-set threshold. Because magnitude is measured, the orientation of the sensor (E-W, N-S, and up-down) is not important; this is unlike a 1-axis gaussmeter. With the VGM the user can set the alarm to 15 gauss (for example) and it will sound (simultaneous with a red light) whenever the field exceeds 15 gauss for at least 5 milliseconds. Using the meter this way, it is easy to make a map of the 15 gauss line (or for whatever threshold is set) around a strong magnet. When using the alarm, of a steel part can be rapidly scanned to show if any areas exceed the set threshold. Then the "peak hold" function can be interrogated, showing the peak values of X, Y, Z (including polarity) and magnitude that occurred during the scan. Peak hold also has a 5 millisecond response time.

  • Digital Leakage Current Tester

    Educated Design & Development, Inc.

    Fast - All operator controls are located on the front panel to expedite testing. The entire test can be performed in a matter of seconds! Pays for itself in time and stress savings. Versatile - Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. Adaptable - Universal rear panel receptacle allows for testing products with any plug configuration. Accurate - True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST. Flexible - A front panel switch permits testing either through the power cord of the product under test, from surface/ patient connection-to-ground, or from surface/ patient connection-to-surface/ patient connection. Portable - Lightweight, with integral handle. Other Features - Product Ground Switching (grounding conductor maintained to device under test when not measuring leakage). Automatic front receptacle disconnect when configured in the 240V test mode (prevents inadvertent connection of 120V when configured for 240V operation). Proven - These are the only leakage current testers designed and supported by Product Safety experts. That is part of the reason why they have become the standard in the industry. Full technical support by experienced safety engineers.

  • Analog Insulation Resistance Tester

    KT-1000i - Kast Eng Co. LTD.

    It is an insulation tester with a F.S(Full Scale) 100 ㎂, 1.5 Class high accuracy analog meter.At first the operator preset the reference value once, then tester measures the insulation of the product and judges Good or Bad.The way to preset the reference value is to push the button and adjust the volume while watching on the meter. The insulation resistance depends on each other product, mostly if the insulation resistance value is higher, the product is better. This tester is suitabe for mass product test.Power supply : AC 220 V, 50 ~ 60 ㎐Output voltage : DC 500 V, DC 1000 VRange of resistance measurementDC 500 V from 0 ~ 1000 ㏁DC 1000 V from 0 ~ 2000 ㏁Auto judgementWhen the tested value is higher than the reference - Good lampWhen the tested value is lower than the reference - Bad lampJudgement time : ± 0.3 sMeasurement precision500 ㏁ ↓ ± 3 %500 ㏁ ↑ ± 5 %Dimension : W 420 × H 160 × D 440 (㎜)Weight : Approx. 10 ㎏Price : 850 (USD)

  • PCI-To-PCI Expansion System

    PCIS-8580-4S - ADLINK Technology Inc.

    The PCIS-8580-4S can expand 4 additional 5V PCI slots to your computer through a cable connection. Any PCI I/O cards, image capture cards, data acquisition cards, or motion control cards in an expansion chassis which is 10 meters away from your host computer. The PCIS-8580-4S is particularly useful for users who need extra 5V PCI slots, or want to place I/O devices in a hazardous environment or away from host computer. The PCIS-8580-4S utilizes the state-of-art ??serialized bridge??technology to expand the PCI bus. PCI bus signals are serialized and transmit in 4-paris, 622Mbps LVDS signals to provides a full 132MB/s PCI bandwidth and a maximal 10 meters expansion distance through a robust cable connection. Furthermore, the PCIS-8580-4S works as standard PCI bridges and is transparent to your computer system. That is, all your applications and drivers can be easily migrated to the PCI-to-PCI expansion system without any modification.

  • UVC Detectors

    PMA 2122 - Solar Light Company Inc.

    The PMA 2122 Germicidal UVC detectors provide fast and accurate irradiance measurements of the effective germicidal radiation. Ultraviolet radiation at 253.7nm has been used in germicidal applications for several decades. The PMA 2122 is designed to be used with the PMA2100 or PMA2200 UV meters / Radiometers.Microorganisms (bacteria) ,usually in air or water, can be killed using UV or a combination of UV and ozone. The UV producing lamps in the purification systems must be monitored to insure that the bacteria are receiving a lethal dose of germicidal UVC radiation. The expensive UV lamps can be monitored to get maximum life out of the lamp before replacement. The germicidal UVC detectors can also be used to insure that the proper lamp has been installed after replacement.

  • ETHERNET COPPER EXTENDER FOR 10/100 NETWORKS, VDSL2

    EIR2-EXTEND - B+B SmartWorx

    Hardened 10/100BSE-TX Ethernet ExtenderExtend Ethernet Copper up to 2200 meters (7218 feet) over existing copper wire (common copper, telephone, Cat5e)VDSL2 technology with transmission rate of 100Mbps at 400meters-40°C to 75°C (-40°F to 167°F) operating temperature rangeAuto -detection of Local/Remote function to reduce installation timeLocal/Remote function to reduce installation timeLink-Down-Relay (LDR) function to inform link loss to other sideOne 10/100Base TX (TX) Ethernet port with RJ-45 connectorIEEE 802.3 10BaseT and IEEE 802.3u 100BaseTX compliantLine port uses common RJ-11 connector

  • Deluxe DMM w/Amp Shutters

    582 - Electronic Specialties Inc.

    *Huge 2 inch LCD Display, easy to see from across the room *Display is backlit for use in Dark Spaces *Amp Shutters prevent mistaken operation, improve safety and saves fuses by blocking unused amp jacks! *Great Meter for Electrical Trouble Shooting *11 Test Functions, 33 Test Ranges *Measures Temp in Both F and C, Probe Included *Desireable 20 Amp Test Range *Modern Design, the Protective Holster is Built-In *Data Hold *Carrying case, Test leads, Temp probe, Instructions and Battery included

  • ANALOG LASER POWER PROBES

    Macken Instruments, Inc

    Laser power measurements should be quick and easy. They should not involve time consuming set-up and alignment problems. Ideally, the measurements should also be able to be made at any point in an optical system where losses are likely to occur. Unfortunately, most laser power meters have sacrificed ease of use to gain continuous power readings. However, in most laboratory and production situations, the usual requirement is for a quick spot-check of power with a minimum of disruption. Even when tuning up a laser, researchers have found that it is best to tune for a desirable mode pattern.

  • Fluxmeter

    Model 2130 - Magnetic Instrumentation Inc.

    The Model 2130 Fluxmeter is a fully featured, high-end Fluxmeter based measurement system. It is a compact instrument with high accuracy, automatic drift correction, microprocessor control, and twelve measurement ranges to allow the operator to configure the meter for maximum resolution and accuracy. The Model 2130 is capable of measuring (DC), alternating (AC), or pulsed magnetic fields. Selecting primary measurement functions is quick and easy with dedicated front panel function keys. An easy to use menu allows access to user defined parameters such as upper and lower magnetic limits and relative magnetic measurements.

  • Protection Device Test Generators

    EMC Partner AG

    Surge generator for testing clamping voltages of protective elements like varistor or transorb diodes with impulse forms 10/000 and 8/20. The current can be measured with the internal peak meter and therefore adjusted to the desired test current. The clamping voltage measurement must be done external direct over the EUT. In addition a combination wave circuit (CWG) is included for EMC test up to 6 kV and 3 kA. The peak output voltage and current of the MIG CWG are indicated on the display. The two BNC monitor outputs allow monitoring the voltage and current wave shapes by an oscilloscope