Showing results: 301 - 315 of 4066 items found.
-
Model N500 -
Teledyne Advanced Pollution Instrumentation
The Model N500 CAPS NOx analyzer uses superior Cavity Attenuated Phase Shift (CAPS) Spectroscopy to measure True NO2, NOx, and NO gases. The instrument combines direct NO2 measurements with highly efficient gas phase titration (GPT) to convert and measure the NO gas component. An automatic baseline reference cycle accounts and compensates for any potential baseline drift due to varying environmental conditions.
-
Model P7 -
Probing Solutions, Inc.
Made from 300 series stainless steel, the P7 probe holders accept all model 407 replaceable probe tips, and are secured with a set screw. When used with the P7 Tool Holder Adapter Arm; “Z” position adjustments are easy, and can accommodate a variety fixtures and probe card holders. Designed for both high temperature (-65 to 300°C) and high electrical isolation measurements.
-
Model 224 -
Telebyte, Inc.
FEATURES: DataSpy® Status Display; Full Duplex & Handshake; Loopback & DTE/DCE Switch; DC to 19.2 KBPS; Supports DTR & DCD; Optically Isolated. The Model 224 RS-232 Line Driver with Control Signals and LCD Display provides for transmission of a handshake signal in each direction, in addition to communicating full duplex data up to 19.2 KBPS and providing complete optical isolation.
-
Model T100 -
Teledyne Advanced Pollution Instrumentation
The Model T100 uses the proven UV fluorescence principle, coupled with a state of the art user interface to provide easy, accurate, and dependable measurements of low level SO2.Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon 'kicker' and advanced optical design combine to prevent inaccuracies due to interferents.
-
Model 212HS -
TREK, INC.
Trek offers a unique, small, and portable Q/m analyzer which utilizes the "draw-off" toner transfer method to yield repeatable high accuracy toner charge measurements. The Trek Model 212HS Charge-to-Mass Ratio (Q/m) Test System is used to quickly and accurately determine the charge-to-mass ratio characteristics of both single and dual component electrophotographic toners and other charged particulates.
-
Model HG-700 -
Magnetic Instrumentation Inc.
The Model HG-700 is a computer-automated, magnetic Hysteresigraph system for measuring the magnetization and demagnetization curves on all types of permanent magnet materials including: hard ferrite, rare earth-cobalt, Nd-Fe-B (Neo), and bonded magnets.
-
Model 7050 -
Pentek, Inc.
- Now available in RFSoC Gen 3 with the Model 7053- Supports Xilinx® Zynq® UltraScale+" RFSoC FPGA- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2, and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional front panel dual optical MPO interface for gigabit serial communication- Unique QuartzXM eXpress Module enables migration to other form factors- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free lifetime applications support- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX- Please refer to the product datasheet for Installed FPGA IP Module details
-
Model 341B -
TREK, INC.
The Trek Model 341B is a DC stable, high-voltage precision electrostatic voltmeter for making noncontacting surface voltage measurements in the range of 0 to ±20 kV DC or peak AC. Research and industrial applications include charge accumulation monitoring of the LCD production processes, monitoring surface potentials in the electrostatic painting process, research and development in the electrophotographic process, and measuring electrostatic potentials on polymers, rubber, fabrics, and paper.
-
Model N901 -
Teledyne Advanced Pollution Instrumentation
The Model N901 is a near-continuous hydrocarbon gas analyzer that measures the concentration of Methane (CH4) and Total Hydrocarbons (THC) in air. The concentration of the non-Methane (NMHC) component is calculated by the subtraction of CH4 from THC, with high sensitivity and accuracy. The hydrocarbons are measured using a Flame Ionization Detector (FID), in combination with gas chromatography (GC). The instruments range and performance are tuned specifically for use in ambient air quality monitoring assessments.
-
Model 201 -
Telebyte, Inc.
FEATURES: Operates with only Pins 2(TD), 3(RD), & 7(GND); Screw Terminals and RJ-11; DTE/DCE Switch; Built in Surge Protection; Male or Female RS-232; 19.2 KBPS, Full Duplex, 2.1 Miles. The Model 201 RS-232 Auto Powered Line Driver requires only TD, RD, and signal ground for power and full duplex operation up to 19.2 K BPS.
-
HSHLD® MODEL 310 -
Oneida Research Services, Inc
ORS manufactures the HSHLD® Model 310 High Sensitivity Helium Leak Detection System, a Quadrupole Mass Spectrometer system for High Sensitivity Helium Leak Rate measurement to qualify your product to the latest, tighter leak rate requirements of Mil-Std-883, Method 1014. Our model HSHLD® Model 310 uses conventional mass spectrometer helium leak test technology. This gives you enhanced spectrometer sensitivity at a modest cost. The system is modular, automated, flexible, fast, easy to calibrate, easy to use, and is affordable. Both the FINE and GROSS leak test is performed in a single test sequence.
-
Model 71640 -
Pentek, Inc.
- View product video- Ideal radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/Ds- 2 GB of DDR3 SDRAM- Sync bus for multimodule synchronization- PCI Express Gen. 2 interface x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Clock up to four modules with Model 7194 High-Speed Clock Generator - PMC/XMC- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Model UDA -
tecsis LP
Model UDA is a universal signal conditioner and amplifier designed for use with all full bridge, strain gage-based transducers. Model UDA turns the analog signal into a user-selectable output of ±5Vdc, ±10Vdc, or 4-20mA. This versatile unit features selectable excitation of 2.5 or 5.0Vdc bridge voltage and has a wide DC power input range from 11 to 28Vdc to adapt to a variety of installations. Model UDA includes a wide zero and span adjustment range and a symmetry adjustment for applications requiring precision in both tension and compression. The configurable low pass filter actively removes unwanted high frequency signal components. The unit is housed in a rugged DIN-mountable enclosure with screw terminals to provide connection for power, analog output, shunt calibration, and sensor signals.
-
Model 78610 -
Pentek, Inc.
Model 78610 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This digital I/O board provides 32 LVDS differential inputs or outputs plus LVDS clock, data valid, and data flow control on a front panel 80-pin connector. Its built-in datacapture and data generation feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
-
Model 1072 -
Aplab Limited
Aplab Psophometer is a portable unit designed for the use of testing telecommunication equipment. It has Psophometric filter, which has the frequency response of the weighing network based on the CCITT recommendations and frequency response characteristics for unweighted measurements. The additional features included in this model are, ‘Recorder out’ available at the rear panel for plotting a response curve, built-in stable calibration signal for calibration check and Lo Battery facility to check the Battery condition.
