Showing results: 5401 - 5415 of 9910 items found.
-
DT3 -
North Atlantic Industries
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
40-616A-021-16/5/1 -
Pickering Interfaces Ltd.
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module is part of our range of reed-relay based switching solutions. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously.
-
40-883-001 -
Pickering Interfaces Ltd.
A 50 Ohm 6GHz multiplexer available as an 8 to 1 MUX in a two slot PXI module or a 16 to 1 MUX in a three slot PXI module. It exhibits low VSWR over the full operating frequency range and consistent and flat insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making it ideal for ATE systems requiring frequent and fast operating RF switching.
-
43-921-001-KIT -
Pickering Interfaces Ltd.
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
Ampere Altra Dev Kit -
ADLINK Technology Inc.
Ampere Altra Dev Kit consists of a COM-HPC Server Base carrier paired with a COM-HPC Server Type Size E module and heatsink with fan.The module features Ampere® Altra® SoC (Arm Neoverse N1-based architecture) harnessing 32/64/96/128 Arm v8.2 64-bit cores for up to 1.7/2.2/2.8/2.6 GHz and providing support for up to 768GB DDR4 memory, offering unprecedented performance and power per watt with exceptional scalability.
-
XA1110 (Qwiic) -
SparkFun Electronics
The SparkFun XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to our Qwiic Connect System. Equipped with the XA1110 GPS module from GTOP, this board utilizes the MediaTek MT3333 chipset, loaded with specialized SparkFun firmware that enables both I2C and serial ports simultaneously. Using I2C means you won’t have to tie up your serial port with GPS, leaving it open to other possibilities.
-
iWave Systems Technologies
The ARINC 818 to DVI converter is a rugged standalone module available in 6U cPCI form factor used for ARINC 818 to DVI conversion, DVI to ARINC818 conversion, ARINC 818 Mux as well as ARINC 818 Duplicator either on front panel or via cPCI back panel. It is a video Converter module designed with Cyclone V GT FPGA, using Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
782385-13 -
NI
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
782385-14 -
NI
The TB-2646B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire dual 4x32 or 1-wire quad 4x32 matrix. You can directly connect the TB-2646B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2646B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
782615-01 -
NI
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at … the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
N6700 Series -
Keysight Technologies
The N6705A is 4-slot mainframe that accepts 1 to 4 modules in any combination. Modules are ordered separately. Maximum output power is 600W. The DC Power Analyzer is designed for bench testing in R&D. It is a highly integrated instrument that combines up to four advanced DC power supplies, DMM, oscilloscope, arbitrary waveform generator and datalogger. It provides an easy-to-use interface, with all sourcing and measuring functions available from the front panel.
-
784175-01 -
NI
The PCB IMID01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMID01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
780985-01 -
NI
The PCB IMIC01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMIC01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
LS1601A -
Universal Switching Corporation
For Communication, Telemetry, ATE and Broadcast Installations. Continuing to expand our distribution product offerings, the new LS1601A offers a fresh new alternative to system engineers. The 3RU rack mountable unit has a unique "open window" front panel design that allows up to sixteen plug-in modules to be installed with both forward and rear facing connectors, controls, and indicators. For control and monitor, a plug-in LXI certified 10/100 Ethernet module can be installed
-
HD2107.1 -
Delta OHM S.r.L.
Centesimal thermometer in the range ±199.99 °C, decimal outside this range, one input for Pt100 probes with SICRAM module measuring range -200 °C +650 °C.