Showing results: 7216 - 7230 of 10255 items found.
-
Y1214B -
Keysight Technologies
The Y1214B Air Inlet Kit can be used to supply additional cooling air from the front of the chassis so that this air is directed to other slots. These air inlet modules utilize the unique cooling design of the M9018B and M9019A PXIe chassis The kit is not supported in any other PXI chassis and may actually decrease cooling capacity in other PXI chassis. Requires some assembly.
-
ROM-5721 -
Advantech Co. Ltd.
Advantech ROM-5721 SMARC 2.0/2.1 Computer-on-Module is powered by NXP i.MX8M Mini SOC which includes up to 4 Arm Cortex-A53 cores in combination with one Cortex-M4 real time processor and Vivante GC320 , GC NanoUltra 3D graphics engine. It provides USB2.0, Gigabit Ethernet, MIPI-CSI, PCI Express, Dual channel LVDS shared with MIPI-DSI for embedded applications.
-
Comware Technical Services, Inc.
With locations in California, Guadalajara MX, and Penang MY, and satellite affiliates worldwide, On-Site Support from Comware is never far away. For competitive pricing, service and quality – Comware is highly qualified to service and maintain your GenRad, Teradyne and Agilent system parts and modules. Our team has 35 years (and counting) experience maintaining the ATE systems you rely on.
-
SC5 -
North Atlantic Industries
Serial Communication Module SC5 provides up to 4 high-speed, programmable RS-232/422/485, individually isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel isolated returns are available as part of the channel user interface signal set (for SE or ISO-GND reference).
-
SC6 -
North Atlantic Industries
Serial Communication Module SC6 provides up to 4 high-speed, programmable RS-232/422/485, individually non-isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel non-isolated returns are available as part of the channel user interface signal set (for SE or SYS-GND reference).
-
SC7 -
North Atlantic Industries
Module SC7 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications. SC7 is the same as SC1 except SC7 reallocates the pins used for CTS Flow Control as four (4) additional system grounds.
-
3508 MMS ECM -
Abaco Systems Inc
The 3508 Electrical Conversion Module (ECM) provides six (6) RS-232 outputs and ten (10) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
5158 -
Abaco Systems Inc
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
CPCI-4SIP-6U -
ALPHI Technology Corporation
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
40-670A-021-99/1 -
Pickering Interfaces Ltd.
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
40-670A-021-S-49/2 -
Pickering Interfaces Ltd.
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
40-670A-022-24/8 -
Pickering Interfaces Ltd.
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
40-670A-022-10/16 -
Pickering Interfaces Ltd.
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
40-670A-022-198/1 -
Pickering Interfaces Ltd.
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
40-670A-022-5/32 -
Pickering Interfaces Ltd.
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).