Showing results: 841 - 855 of 10255 items found.
-
SX-PCEAC2 -
Silex Technology
The SX-PCEAC2 is powered by Qualcomm Atheros radio chip, the QCA6174-5, which features 2x2 wave 2 MU-MIMO technology. It is a dual-band 802.11 a/b/g/n/ac module with Bluetooth support which is designed for devices that require wireless connectivity in a small form factor combined with high performance with throughputs reaching up to 867Mbps.
-
ICS Electronics
*Enclose any VXI module with these one, two and three slot-wide kits. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
ART103 -
Vadatech Inc
The ART103 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC103 carrier board. The ART103 is a passive RTM that allows for the additional connectivity of two GbE ports, Management 10/100Mbit Ethernet, Management RS-232 serial interface and three PCIe x4 lanes for expansion. One of the PMC J4s (user defined I/O) is routed to the back.
-
51-921A-001 -
Pickering Interfaces Ltd.
The use of the StarFabric interface operating at 2.5Gb/s minimizes the impact on system speed. The PCI interface of the 51-921A supports both 32 bit and 64 bit operation and backplane speeds of 33MHz and 66MHz, ensuring the highest speed operation under all conditions. The StarFabric interface ensures the modules perform seamlessly with no impact on the test system software.
-
SoM3-MPF300T -
Sundance Multiprocessor Technology Ltd.
The SoM3-MPF300T is a small footprint System On Module (SoM) with 40x50mm dimensions. It has a low power, highly secure FPGA from the PolarFire family from Microsemi. It comes with 4GB of DDR4 memory, Ethernet PHY, and FLASH. This SoM is ideal for being used in complex hardware designs, and is compatible with Sundance SoM carriers SE215 and EMC2-DP-V2.
-
Virginia Panel Corporation
VPC rack mountable receivers like the 9075 meet the standards essential to support advanced mass interconnect requirements. The 9075 receiver is designed to accept the 9025, 9050, 9050 VXI, and 9075 ITA and can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed to create custom interfaces which are ideal for functional and system testing applications.
-
TE2504 -
Ajinkya Electronic Systems
Ampere Hour Meter Module- Model TE 2504 is basically managed for ready setup or the usage can be seen in where the current requirement are low. This one is used which is ready to be applied in the stand alone panel and advanced from all the former models, IM2501, IM2502 and IM2503. These are basically panel mount instruments which are required to rectified in the rectifier or in an independent panel.
-
D Series -
Introspect Technology, Inc.
With the invention of the D Series line, Introspect Technology has revolutionized the way product engineers test high-speed digital applications. Our unique plug-in module design allows for high-performance testing on any load board and eliminates the need for cables. Despite the continuous transformation of the test industry in recent years, a growing number of legacy equipment remain in use.
-
ROM-2620 -
Advantech Co. Ltd.
Advantech ROM-2620 OSM 1.1 Computer-on-Module is powered by NXP i.MX 8ULP SoC which includes up to 2 Arm Cortex-A35 cores in combination with one Cortex-M33 real timeprocessor and Vivante GC7000 nanoULTRA/GC328 graphics engine. It provides USB2.0, Fast Ethernet, MIPI-CSI, I2C, SPI, GPIO, PWM and MIPI DSI display for embedded applications
-
ROM-2860 -
Advantech Co. Ltd.
Advantech ROM-2860 OSM 1.1 Computer-on-Module is powered by Qualcomm QCS6490/5430 SoC which includes up to Arm v8 Cortex® in combination with Andreo GPU 643 and Andreo VPU 633 graphics engine. It provides PCIe, USB 3.2, Giga Ethernet, MIPI-CSI, I2C, SPI, GPIO, PWM and eDP, DP, MIPI-DSI display for embedded applications.
-
TA102A -
MSA
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
EM2 -
U. S. Digital
The EM2 provides digital A & B quadrature outputs with a third output index channel. Each EM2 module is resolution specific and is matched to the resolution of a code wheel. The EM2 operates with a single 5V supply and provides single ended outputs which are capable of both sinking and sourcing 5mA. An internal 0.1 uF decoupling capacitor is designed into the EM2 to provide enhanced noise immunity.
-
FMC410 -
Sundance Multiprocessor Technology Ltd.
The FMC410 is an optical transceiver module in the FMC form factor that offers ten independent optical transmit and receive links with maximum data rates of either 6.25Gbps or 10Gbps. This COTS card provides high-speed optical input and output for telecommunications, data networking, data storage, and ultra-high-definition video applications. The FMC410 can also be used as a dual 10Gb or dual 40Gb Ethernet port.
-
ART108 -
Vadatech Inc
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
SHF Communication Technologies AG
SHF provides a wide range of high speed modules suitable e.g. for SONET OC-768 / SDHSTM-256, 100 GbE, 400 GbE, 1TbE or Fibre Channel telecommunication systems . The needs of our customers are different; therefore SHF is happy to offer customization to specific applications. A small selection of such assemblies based on our standard product offerings can be found in the customized assemblies subsection.