Showing results: 8536 - 8550 of 10255 items found.
-
MODEL LCA-RTC -
Transducer Techniques, Inc
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
PQM-703 -
Sonel S.A.
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
Pickering Interfaces Ltd.
Simulation of resistance based temperature sensors such as positive or negative temperature coefficient thermistors. Resistance Temperature Detectors (RTDs) can be wire-wound or thin film. Our RTD simulator modules provide a cost-effective method of simulating both PT100 and PT1000 RTD sensor types that require fine setting resolution.
-
AFI-400 -
Shanghai Fibretool Technology Co.,Ltd.
AFI-400 Optical Fiber Identifier is an important tool for optical maintenance, which is used for nondestructive fiber identification work, can be detect in any location of both SM and MM fiber. Meanwhile it also has Visual Fault Locator module with fault location function. It is the ideal instrument for online test.
-
Thorlabs, Inc.
Thorlabs offers the PRO8 modular test and measurement platform in 2-slot and 8-slot configurations. These customizable bench top chassis let users build a compact fiber or laser diode testing platforms for their lab or factory floor. Modules include lasers, TEC controllers, optical switches, and current controllers.
-
ThermalAir TA-3000A -
MPI Thermal Test Systems
The ThermalAir TA-3000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -65°C to +225°C. Compact! Plus Performance!
-
ThermalAir TA-3000B -
MPI Thermal Test Systems
The ThermalAir TA-3000B high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -65°C to +225°C. Compact! Plus Performance!
-
SCS-817 -
Alligator Technologies
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
W-IE-NE-R, Plein & Baus GmbH
The Mpod micro-1 crate is the smallest and low cost option for the WIENER multi-channel high and low voltage power supply system. The Mpod micro mainframe can house 1 plug-in low or high voltage modules. The integrated Mpod controller card provides10/100 Ethernet, CAN bus and USB-2 interfaces.
-
MKS Instruments
MKS modular vacuum transducers feature compact size that dramatically reduces installation costs. These vacuum/pressure gauges are ideal for applications where controller size and local control are critically important. They are available as pressure transducers with an analog output, or as vacuum modules with digital communications used to transmit the pressure signal.
-
HEAD acoustics GmbH
Sound, vibration, status and reference variables, voice, audio data and more: HEAD acoustics is setting the standard in data acquisition. We offer flexible systems for mobile applications and operation in the laboratory. Our data acquisition systems can also be expanded flexibly using various software and hardware modules.
-
GX3722 -
Marvin Test Solutions, Inc.
The GX3722 is a user configurable, FPGA-based, 3U PXI card which employs a multi-function, analog / digital, I/O daughter board. The module offers multiple analog and digital source / measure capability. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers selective RF level detectors for air interface monitoring. The detectors are especially designed for frequencies used in e.g. electron accelerators. Due its mechanical design, the modules are compatible to cable route mounting systems. The detection of unintentional RF radiation is a main application field.
-
DAS1800 -
B&K Precision Corporation
The DAS1800 can be configured for a wide variety of applications with slots for 10 input modules each supporting 4 or 8 measurement channels. Acquire data from any sensor with a voltage or current output (with shunt), or directly measure voltage, resistance, or temperature using thermocouples or resistance temperature detectors (RTDs).
-
M9195B -
Keysight Technologies
The Keysight M9195B PXIe digital stimulus/response (PXI DSR) module is ideal for IC design validation and production test environments. The PXI DSR provides 16 bi-directional digital channels with programmable logic levels and can be configured for synchronized cyclized digital data, for parametric measurements, or for static digital IO.