Showing results: 331 - 345 of 429 items found.
-
Weice Testing Instrument Co.,Ltd.
Weice Xenon Test Chambers (Xenon Arc Test Chambers) are used to induce property changes associated with the effects of sunlight, moisture, and heat. The property changes include cracking, color fading and yellowing could be simulated just in few days and weeks.
-
SSR-15 -
Dwyer Instruments Inc.
Model SSR-15 Intrinsically Safe Relay offers low power switching with solid state reliability and eliminates explosive conditions. Units are completely encapsulated and impervious to dust, moisture, or foreign material. Model SSR-15 can be mounted in any orientation and is shock and vibration resistant
-
RC612 -
Leco Corp.
The RC612 quantifies the carbon and water present in various organic and inorganic samples, and identifies the source of several types of carbon content. The large diameter reaction tube supports moisture analysis on a variety of sample types including powders, flat strips, or sections of tubes.
-
TRANSPORT X -
GE Digital Energy
The Kelman TRANSPORT X is a compact portable Dissolved Gas Analysis (DGA) system which can be used to analyze oil samples for all dissolved fault gases and moisture. If abnormal levels are detected, it further provides a diagnostic using various IEEE/IEC approved interpretation rules.
-
Omega Engineering, Inc
Omega offers a wide selection of multi-variable handheld temperature, humidity, dew point, and moisture meters. For data analysis choose a meter with data logging capability.
-
Honeywell Sensing & Control
Honeywell's analogy telemetry rotary torque systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements.
-
National Technical Systems
Conformal coating is applied to electronic circuits to provide a protective barrier to moisture and contamination and to provide electrical insulation. The most common specifications used for conformal coating testing are IPC-CC-830B, Amendment 1: Qualification and Performance of Electrical Insulating Compound for Printed Wiring Assemblies and MIL-I-46058.
-
Kharkovenergopribor Ltd.
The main functions of electrical insulating oils are heat dissipation and reliable insulation of energised parts of electrical installations. During the normal operation, moisture and other impurities penetrate into insulating oils, leading to a deterioration of their dielectric properties. This in turn may result in catastrophic failures of critical electrical equipment.
-
Alpha Moisture Systems
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
XLS+ -
Atlas Material Testing Technology
The SUNTEST XLS+ is used to check for property changes of materials and products caused by sunlight, temperature and moisture in a short period of time. The aging which, outdoor or indoor, may take place over months or years, such as fading, yellowing or loss of strength, can often be simulated within weeks inside a SUNTEST.
-
MINITRANS -
GE Digital Energy
Based on the same core technology as the highly successful TRANSFIX the MINITRANS is a lower cost alternative, monitoring three key gases: Hydrogen, Acetylene and Carbon Monoxide (in ppm) plus moisture in oil (%RH & ppm). The measurement of these gases allows the user to detect a wide range of developing faults including arcing.
-
Silex Technology
Its industrial temperature support, robust enterprise security and 802.11ac capabilities make it an ideal solution for applications like factory automation with demanding environmental conditions such as with extreme temperatures, dirt, dust, moisture, shock, and vibrations. Its low power consumption also makes it suitable for portable handheld devices.
-
Reltech Limited
Preconditioning is performed prior to package level reliability testing to simulate the effects of board assembly on non-hermetic devices where moisture may have been absorbed during normal storage. The subsequent exposure to high temperature during infra reflow assembly can cause internal damage such as “pop corning” and delamination.
-
BKPR-4 -
MISCO Refractometer
With scales for Honey Moisture, Honey Percent Solids, Honey Specific Gravity, and Honey Density, the MISCO BKPR-4 Digital Honey Refractometer is ready for use by government honey inspectors, professional beekeepers, honey producers, honey mixers, honey brokers, or anyone requiring the absolute most accurate, repeatable honey measurements.
-
MULTITRANS -
GE Digital Energy
The MULTITRANS is an 8-gas on-line transformer DGA monitoring unit designed to monitor a bank of three single-phase transformers in close proximity. Based on the same core technology as the highly successful TRANSFIX the MULTITRANS measures all significant fault gases (in ppm) as outlined by international standards as well as moisture in oil (%RH & ppm).