Showing results: 346 - 360 of 2773 items found.
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
CallerIP -
Visualware, Inc.
IP and Port monitoring. See all incoming and outgoing connections made to your computer. Including process names, remote and internal port numbers and much more. Automated alerts bring your attention to illegal connections. Automated Alerting. Set up alerts to warn you of intruders and hack attempts. CallerIP can send an email, display a warning dialog and/or append a log file. CallerIP Server. CallerIP server allows you to view all incoming and outgoing connections to your computer from any browser in the world. CallerIP plots all connecting IP locations on a world map. IP origin shown on world map. All connecting IP address locations are shown on a world map.
-
MP-50 -
FRANKONIA GmbH
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Test Chest 3G (Multi Function Test) -
Murraypro Electronics
Quick and very easy to use, the amazing Test Chest boasts instantaneous Audio + Video generation and Monitoring. NO tedious boot-up means Test Chest is “First out of the blocks” every time by 10s of seconds, and it’s intuitive touch-screen speeds Engineers to the required function, saving precious time and giving their investigations a real head start. 10bit precision signal generation is standard with Test Chest, as are the analysis utilities which are displayed on it’s superb 5” high resolution touch screen Monitor screen, and stereo sound too (when present).Ease of use and protection whilst in service are serious matters, so Test Chest is fitted with ‘Ez-Grip’ resillent rubber end sleeves; these assist grip, and provide additional protection against everyday knocks and bumps. During transportation your Test Chest’s tough extruded alloy housing is cradled within a customised go-anywhere foam lined ABS Carry-case for complete protection.
-
Hawk® EMS -
International Medcom
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
Keynote Systems, Inc.
Application performance management (APM) is critical to business success today. Dynatrace automatically sees and analyzes every single user transaction, all the time. All relevant metrics, environment changes, and application deployments are shown in real-time.
-
motadata -
Mindarray Systems, Inc.
Motadata is an IT analytics software product that derives business insights through real-time processing, correlation and intelligent visualization of NOC.
-
Schwarzbeck Mess Elektronik
Linear polarized half-wave dipole with 1:1 balun and fixed element length for fieldstrength measurements at TETRA (terrestrical trunked radio) networks.
-
Crystal instruments
The specially designed EDM-RCM software simultaneously connects multiple such Spider systems in addition to providing updated results of essential data for all Spider front-ends located throughout the world. The software provides a live view of data from any Spider system as needed and downloads recordings from any or all Spider front-ends for further analysis and inferences.
-
HHD Software Ltd.
The library lets you enumerate all installed serial devices, including, but not limited to serial ports and modems. All kind of PnP serial devices as well as virtual devices are also supported. After you get an instance of the serial device, you can create a monitor object and attach to the device to receive monitored data and events. The Monitor object can be attached to the device at any time, no matter if the device is being currently used or not. You can also detach from the device at any time.
-
SlimWave® -
Sercel Group
SlimWave is a small diameter digital multi-level downhole seismic array for up to 24 levels. Technologically advanced, it excels in very small diameter wells or any completion restriction.
-
TH-8/AOP -
Physitemp Instruments
The TH-8/AOP is one of our most economical precision thermometers in the Physitemp product line. The TH-8 offers the same high accuracy (0.1°C ±1 digit) and resolution as all our other thermometers, but with a narrow temperature range. The TH-8 has a temperature range 0f -10 to +60°C with 3 probe inputs. The TH-8 is also switchable from celsius to Fahrenheit. The TH-8 is ideally suited for either a laboratory or hospital setting where continuous temperature readings within the physiological range are sufficient.
-
SL Corp.
Detect and respond so fast, they won’t even know it happened.
-
AMETEK Drexelbrook
The Drexelbrook 560 DRX Series wireless products feature 900KHz frequency hopping, spread spectrum technology to provide a reliable, license free, wireless link between the field instrument and the control room.These wireless interface products provide a cost effective alternative to expensive hard wired connections.Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference.
-
RTM 4K -
Video Clarity, Inc.
4K or multi-channel HD with 12G-SDI Interfaces Optional 10G IP for ST 2110 Networks
