Filter Results By:
Products
Applications
Manufacturers
-
product
Combustion Efficiency Analyzers
Test Products International, Inc.
Determine combustion efficiency, CO2, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.
-
product
Continuous Gas Analyzer In Flue Gas
NSA-308
The NSA-308 can measure five components NOx, SO2, CO, CO2, and O2 in exhaust gas from incineration facilities, etc. Two analyzers are used, a high-performance, high-functionality ratio infrared analyzer and a magnetic wind oximeter.
-
product
Gas Analyzers
FUJI developed the first infrared gas analyzer in Japan to use mass-flow sensors. Since then, we have supplied customers with various types of gas analyzers to support environmental preservation and control efforts. These efforts include measurements of atmospheric pollution and detection of low density of SOx and NOx, generated by incinerating facilities and boilers. FUJI's gas analyzers are widely used to monitor the atmosphere to help maintain a cleaner natural environment.
-
product
High-concentration, High Flow Ozone Generator
SEMOZON® AX8407
The SEMOZON AX8407 generator converts pure oxygen into ozone through silent electrical discharge and achieves high output and high concentration level. It requires only minute levels of dopant nitrogen gas, far below the levels required for competitive ozone generators. As a result, the presence of contaminants, e.g. NOx compounds, is extremely low.
-
product
Portable Exhaust Gas Analyzer
IMR 1440FL
IMR Environmental Equipment, Inc.
The exhaust gas analyzer, IMR 1440FL/COFL, is designed to measure exhaust gases of Forklift Trucks that are powered by a variety of fuels. According to US regulations, the IMR 1440FL/COFL can measure soot and CO for Forklift Trucks. If state regulations require NOx, the IMR 1440FL/COFL can be equipped with a NOx sensor. The IMR 1440COFL is equipped with two CO sensors. One CO sensor operates in the low range and another CO sensor operates in the high range.
-
product
Solid-State Chemiluminescence NOx Analyzer
CL3020
CL3020 CLD NOx analyzer utilizes next generation solid state detection technology to measure low and ultra-low NOx in combustion applications.
-
product
Transportable NOx-O2 Gas Analyzer
NOA-7100
The NOA-7100 adopts the normal pressure chemiluminescence method is adopted for NOx measurement, and the zirconia method is adopted for O2 measurement. NOA-7100 is “All-in-one portable analyzer” that incorporates the pretreatment parts needed for measurements. Switching between eight ranges from 25 to 4,000 ppm supports a wide range of NOx measurements. The NOA-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
-
product
Nitrogen Oxides Analyzer (NO-NO2–NOx)
AQMS-600
–NOx) analyzer utilizes chemiluminescence technology indicated by US EPA as the federal reference method for monitoring multiple forms of nitrogen oxides.
-
product
Continuous Emission Monitoring System
CEMS
CEMS, the “Environmental Eye” for Source Emissions.A Continuous Emission Monitoring System (CEMS) is an integrated system to measure fuel flow, dust, and concentrations of air pollutants such as SO2, NOx, CO, CO2, THC and O2 in accordance with the applicable regulations for the emission source.
-
product
Ammonia Analyzer (NOx,NH3)
AQMS-650
FPI AQMS-650 measures NH3 in the ambient air, which delivers a stable and precise value. It adopts chemiluminescence technology with an external converter that can combine its use with AQMS-600 measuring NOx; during the measurement, NH3 will be converted into NO by oxidation. And it also comes with its own developed software. The remote PC software allows for a remote connection with a virtual interface and data downloading capability to operate the software.
-
product
Combustion
Our combustion gas analysers are compatible with a wide range of machines, such as engines, industrial boilers, incinerators and industrial furnaces. They can be used to assess various combustion parameters, from efficiency and yield to CO, O, NOx and other gas concentrations in flue and exhaust gases.
-
product
Heated Type NOx Analyzer
MEXA-1170HCLD
The MEXA-1170HCLD is available as an atmospheric (A) and a vacuum (V) model. With nine ranges available from 10 ppm up to 10,000ppm, these instruments are designed to fit most applications in the industry.
-
product
Residential/Commercial Combustion Analyzer w/ NOx Sensor
C165+N
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
product
Residential/Commercial Combustion Analyzer Kit w/ NOx Sensor/ Oil-Fired Appliances/ Printer
C165+NOILKIT
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
product
Residential/Commercial Combustion Analyzer Kit w/ NOx Sensor/Printer
C165+NKIT
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C165+ Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. The new LINK feature connects the included wireless pipe clamp temperature probes and other optional probes to the C165+. Essential information for installing and maintaining furnaces and boilers all in one device.
-
product
Multi-Stage Injection Analyzer
FJ-8000 series
Common rail method already is commonly known as an injection system of diesel engine now. That system enables multi-stage fuel injection by offering high injection pressure in various driving situation. Adopting the common rail system helps improving fuel consumption, reducing noise and vibration, because the system can make the fuel approximate complete combustion which suppresses PM and NOx generation. FJ-8000 series is the multi-stage injection analyzer that supports more accurate injection by measuring injection quantity, injection rate, injection timing, and injection period by multi-stage injection of common rail system in the environment that is near to an actual vehicle environment.
-
product
Washwater Monitoring System
EG-100
Washwater Monitoring System for NOx and SOx Scrubber.Monitoring pH/Temperature, Turbidity, and PAH.EG-100 has flow type sensors.
-
product
Marine Emissions Analysers
Protea 2000
The Protea 2000 emissions monitoring system is approved for the analysis of exhaust gases from the engines and boilers of ships and offshore rigs. Robust and with proven reliability, up to six gases can be measured including SO2, CO2 and NOx.
-
product
Conventional Extractive System
ML660
The Teledyne ML®660 conventional extractive system is designed to extract and condition hot, wet stack gas for a dry basis measurement of any combination of SO2, NOx, CO, CO2, and O2. This system can be configured specifically for 40CFR60, 40CFR63, 40CFR75 compliance, and process control applications.
-
product
Exhaust Gas Measurement Modules
Reliable and precise acquisition of exhaust values: For exhaust gas measurements, i.e. Lambda, O2, NOx, and NH3 in vehicles with petrol, diesel, CNG or LPG engines CSM has expanded its product portfolio with the CAN-based exhaust gas measurement modules from ECM.
-
product
Gas Measuring Instruments
N Series
Teledyne Advanced Pollution Instrumentation
N Series Gas Measuring Units for SO2 (Sulfur Dioxide), NO, NO2, NOX (Nitrogen Oxide, Nitrogen Dioxide), CO (Carbon Monoxide), CO2 (Carbon Dioxide), O3 (Ozone), True, Direct NO2, NOX, NO, CH4 (Methane), THC (Total Hydrocarbons), and more
-
product
CAPS True NO2-NOX-NO Analyzer
Model N500
Teledyne Advanced Pollution Instrumentation
The Model N500 CAPS NOx analyzer uses superior Cavity Attenuated Phase Shift (CAPS) Spectroscopy to measure True NO2, NOx, and NO gases. The instrument combines direct NO2 measurements with highly efficient gas phase titration (GPT) to convert and measure the NO gas component. An automatic baseline reference cycle accounts and compensates for any potential baseline drift due to varying environmental conditions.
-
product
High Range Chemiluminescence NO/NO2/NOX Analyzer
Model T200H
Teledyne Advanced Pollution Instrumentation
The Model T200H combines the proven chemiluminescence principle with a number of innovative features to provide reliable and repeatable NO, NO2, and NOx measurements for extractive type CEM systems. A high-efficiency stainless steel thermal NO2 converter provides durable and consistent operation under the harshest conditions (other converter options also available).The T200H may be fitted with an optional, internal paramagnetic O2 sensor or an infrared absorption CO2 sensor, reducing integration and operating costs significantly.
-
product
High Range Chemiluminescence NOX-NO2-NO Analyzer
Model N200H
Teledyne Advanced Pollution Instrumentation
The Model N200H uses the proven chemiluminescence detection principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of high-level Nitric Oxide (NO), Nitrogen Dioxide (NO2) and total Nitrogen Oxides (NOx) gases for use in extractive type CEM systems.
-
product
Trace-level, Photolytic, True NO2/NO/NOx Analyzer
Model T200UP
Teledyne Advanced Pollution Instrumentation
The Model T200UP provides trace level measurements of NO and NO2 using our Model T200U NOx analyzer combined with a patented high efficiency photolytic converter. Even low temperature molybdenum converters transform other nitrogen-containing compounds such as HNO3, PAN, etc. to a considerable extent. Simultaneous measurements of NO2 performed with molybdenum and photolytic converters have shown significantly different results in the presence of such compounds.
-
product
Trace-Level Chemiluminescence NO/NO2/NOx Analyzer
Model T200U
Teledyne Advanced Pollution Instrumentation
The Model T200U Trace-level NO/NO2/NOx analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is designed to allow ultra-sensitive measurements with a lower detectable limit of 50 ppt while still meeting the requirements for use as a US EPA compliance analyzer.The Model T200U combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer.
-
product
Mid-Range Chemiluminescence NO/NO2/NOX Analyzer
Model T200M
Teledyne Advanced Pollution Instrumentation
The Model T200M combines the proven chemiluminescence principle with a number of innovative features to provide reliable and repeatable NO, NO2, and NOx measurements for extractive type CEM systems. The option of either a molybdenum converter or a high-efficiency stainless steel thermal NO2 converter allows the T200M to be used in a variety of extractive CEM systems, from gas turbines to coal-fired boilers.
-
product
Photolytic True NO2/NO/NOx Analyzer
Model T200P
Teledyne Advanced Pollution Instrumentation
The Model T200P provides measurements of NO and NO2 using our Model T200 NOx analyzer combined with a patented high efficiency photolytic converter. Even low temperature molybdenum converters transform other nitrogen-containing compounds such as HNO3, PAN, etc. to a considerable extent. Simultaneous measurements of NO2 performed with molybdenum and photolytic converters have shown significantly different results in the presence of such compounds.In the photolytic process the sample gas passes through a cell where it is exposed to light at a specific wavelength from an LED array. This causes the NO2 to be selectively converted to NO with negligible interference from other gases. Advances in the photolytic converter technology now yields NO2 conversion efficiency that is similar to molybdenum under typical ambient NO2 concentrations, but without the same interferences.
-
product
Chemiluminescence NOX-NO2-NO Analyzer
Model N200
Teledyne Advanced Pollution Instrumentation
The Model N200 uses the proven chemiluminescence detection principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of low-level Nitric Oxide (NO), Nitrogen Dioxide (NO2) and total Nitrogen Oxides (NOx) gases.
-
product
Chemiluminescence NO/NO2/NOX Analyzer
Model T200
Teledyne Advanced Pollution Instrumentation
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.
