Showing results: 1606 - 1620 of 2129 items found.
-
HWA4200 (With SNMP) -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4200 series, is designed for C-Band 44 waves or 88 waves DWDM system design Line Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
Ultraview Corporation
Ultraview's ethernet based acquisition boards bring low noise, large channel count solutions to common open-source platforms. The flexibility of being able to combine a large number of publicly available firmware/software modules with laboratory quality data acquisition chips makes many previously difficult project integrations possible at a fraction of the cost of developing the entire system.
-
FSVA3000 -
Rohde & Schwarz GmbH & Co. KG
Analysis bandwidth of up to 1 GHz, outstanding phase noise of –120 dBc/Hz and a high dynamic range give the R&S®FSVA3000 signal and spectrum analyzer everything needed for demanding 5G NR measurement applications. High measurement speeds and easy usability make it ideal for demanding signal analysis, both in the lab and on the production line.
-
ATE Systems
ATE Systems has developed a wide variety of custom test systems that integrate commercial test instruments and custom hardware, tied together with a test executive. Examples of the types of tests that have been incorporated include: S-parameters (gain, return loss, VSWR, etc), Noise figure, Power, Spectral response, Linearity, Voltage, Current, Switching speed and so on
-
Anderon Meters -
MOTOMEA
*Measures the anderon value in an assembled bearing.*Detects slight surface irregularities arising from machining imperfections and other factors.*Detects displacement in a radial direction caused by rolling surface irregularities.*Provides the “anderon” value, a numerical expression of the degree of vibration and noise in the bearing, allows quantitative assessment of bearing performance.*Enables the discovery of the causes of vibrations (scratches on the raceways of outer and inner races made during machining, scratches on ball surfaces, contamination by dust particles, etc.).*Enables the sorting of bearings by precision class and more accurate assessment of bearing quality.*Development of high-quality products: aids in the development of high-quality, durable bearings that generate minimal vibration and noise.*Assurance of product quality: allows data to be gathered that can be used for objective assessment of quality, particularly vibration and noise characteristics.*Optimal management of products by quality: High-sensitivity detection of minute but critical variations in product characteristics, allowing to sort bearings accurately by quality for optimal product management.*Improved productivity: allows inspection of bearings before installation in high-precision, high-performance products susceptible to vibration, minimizing defects in assembled products and improving productivity.*Optimal parts control in the open market environment: permits high-accuracy acceptance inspections of delivered parts, allowing to test various samples obtained from both domestic and overseas manufacturers to help secure parts that offer optimal quality.
-
NI
The C Series Voltage Input Module helps you work with voltage measurement applications. This module features isolation to separate channels from each other, from COM, or from earth ground for safety, noise immunity, and high common-mode voltage range. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. You can use included options such as configurable input ranges, output channels, various connectors, and enclosed or non-enclosed modules.The C Series Voltage Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Seeed Technology Inc.
Frequency band: 240 - 960 MHz and 2.35 – 2.55 GHzFrequency span: 112KHz - 100MHzGraphics LCD 128x64 pixels, great visibility outdoorsPC Windows client supports Windows XP/Vista/Win7 both 32 and 64bitsBacklight for great indoor visibility2 standard SMA 50 ohms connector, one for Sub-GHz wideband Nagoya NA-773 telescopic antenna included and another one for 2.4GHz band with helical antenna included.Amplitude resolution: 0.5dBmDynamic range: -115dBm to 0dBmAbsolute Max input power: +5dBmAverage noise level (typical): -110dBm2.4GHz RF Generator amplitude: -30dBm to +1dBmFrequency stability and accuracy (typical): +-10ppmAmplitude stability and accuracy (typical): +-3dBmFrequency resolution: 1KhzResolution bandwidth (RBW): automatic 2.6Khz to 600KhzWeight: 185gSize: 113x70x25 mm
-
TG251xA/501xA Series -
Aim-TTi
One or two channels0.001mHz to 50MHz/25MHz range; 14 digits or 1uHz resolution.Standard waveforms include sine, square, ramp, pulse, sin(x)/x, noise, exponential, logarithmic and PRBS.True pulse generator with variable delay and variable rise/fall.Arbitrary waveforms of up to 128K points at up to 125MS/s.Waveform storage using USB flash drives.Large graphic LCD with simultaneous text and waveform display.Comprehensive internal and external digital modulations including AM, FM, PM, PWM, FSK, BSPK, Sum and PRBS.20mV to 20V pk-pk output from 50Ohms ; plus multi function aux. out.Storage for multiple instrument set-ups in non-volatile memory.Waveform Manager Plus for Windows software included.Programmable via USB and LAN (LXI) interfaces; GPIB optional
-
NI
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
ENVIROMUX-IMD -
Network Technologies Inc
Registers movement in the area covered. Condition display via LED. Provides immunity from common-mode signals such as the effect of strong hot or cold air currents, variation in ambient temperature, background radiation and acoustic noise. 24 dual-element detection zones for long, mid and short range protections. Surface or corner mounting. Pulse count or single shot triggering. Good RFI protection. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Includes mounting bracket for installing the sensor to a ceiling or wall. Regulatory approvals: CE, RoHS.
-
HF2LI -
Zurich Instruments AG
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
Sample Technology
The need for microwave test and measurement technology is even more urgent than the need for microwave equipment itself. Therefore, Shengbo Technology is relying on its own research and development capabilities to strive to become one of the comprehensive microwave test and measurement equipment suppliers. We provide a wide range of RF microwave test products, including a good-quality full-band broadband up-down converter . You can provide 2GHz real-time bandwidth signal up-down conversion function in the frequency range of 0.1 ~ 40 + GHz. With our channel simulator , we Became the first company in the world to provide channel analog solutions in such a wide range of broadband signals. At the same time, we are also an innovativesupplier of noise sources and multi-channel microwave signal sources in the industry.
-
Type NVF-2 -
National RF, Inc
The Type NVF-2 series of handheld directional antennas are used to locate interfering signals or noise in either the 420 – 470 MHz (Type NVF-2A) or the 900 MHz ISM band or cellular telephone bands (Type NVF-2B). Both models incorporate a solid reflector positioned behind a resonated half wave driven element, both elements being mounted on a fiberglass rod with an integral pistol grip. The configuration of the reflector and driven element are such that a deep null in the signal being received will occur when the antenna is pointed in the direction of the signal being radiated. A T-pad resistive attenuator is also incorporated in the antenna mounting enclosure to aid in the direction finding process on very strong signals or when excessive reflections present multiple returns.
-
8230 AJ -
Safran Federal Systems
The 8230AJ anti-jam antenna is a high gain (40 dB) GNSS outdoor antenna with a unique conical antenna pattern that rejects interference from the horizon. The antenna rejects signals at lower elevation angles – where most of the interference comes from – and only receives signals from higher elevation angles where the true satellites are. This way, you get all the performance and timing accuracy you would with a standard antenna plus 20 dB or more of interference rejection.It uses a three-stage low noise amplifier, a mid- section SAW, and a tight pre-filter to protect against saturation by high level sub-harmonics and L-band signals. The antenna covers GPS L1, GLONASS L1, BeiDou B1, Galileo E1, and QZSS L1.
-
Teledyne Marine Benthos
The Benthos Directional Acoustic Transponder (DAT) is anextension to the Teledyne Benthos ATM-900 Series modem, which automatically estimates the azimuthal and vertical arrival angles of a message sent by a remote modem. The system is a modified ultra-short baseline (USBL) which uses a broadband component of a typical modem message to form estimates of arrival angle(s). While conventional USBL devices employ tonal signals, our appropriate processing of wide band signals provides far better combined range and arrival angle estimation, especially at low Signal to Noise Ratio (SNR). Our device offers a clear 360 degree field of view in azimuth, and an approximate vertical coverage spanning + 90º overhead to -50º below horizontal.
