Showing results: 571 - 585 of 2138 items found.
-
Pulse Instruments
Imaging devices, such as CCDs, IR FPAs, and CMOS image sensors, require DC bias with very low electrical noise to prevent contamination of the image. Image quality can also be enhanced by carefully tuning each bias voltage to extract the maximum signal/noise ratio out of an array. Pulse Instruments has decades of experience providing DC bias supplies with the flexibility required tocharacterize and test a variety of devices while maintaining the noise immunity required for satellite and astronomy applications.
-
N9040B -
Keysight Technologies
See the real performance of your design with wider (to 1 GHz), deeper views of the most challenging signalsMeasure the spectral purity of your design with industry-leading phase noise and 78 dBc spurious-free dynamic range across 510 MHz bandwidthExtend RF input frequency up to 110 GHz with Keysight smart mixers; to THz with 3rd party solutionsCapture intermittent signals with gap-free real-time spectrum analysisCapture lower-level spurious signals with an improved DANL low noise path
-
E8267D -
Keysight Technologies
Test advanced receivers with realistic wideband radar, EW and Satcom waveforms with metrology-grade performance and versatile capabilitiesSimulate complex electromagnetic environments with up to 4 GHz of bandwidthReduce the time you spend creating complex signals with Signal Studio software: pulse building, noise power ratio (NPR), multi-tone signals, wireless & moreMaster your most complex signal requirements with the industry's best SSB phase noise: 143 dBc/Hz at 1 GHz (10 kHz offset)
-
APIMS -
Barron Associates
Surface pitting processes are ubiquitous in material science and engineering applications. Rigorous analysis of surface pitting features is time-consuming and error-prone whenever manual measurements are employed. Barron Associates’ APIMS software eliminates the need for tedious manual pit measurements. APIMS analyzes digital surface profilometry data and automatically identifies the location and size (width and depth) of surface pits. APIMS provides built-in noise reduction features to enhance performance and reduce both measurement noise and surface tilt.
-
Newport Electronics
These New Focus high speed fiber-optic receivers offer bandwidths up to 38 GHz for receiving fiber optic data while delivering the lowest noise and cleanest responses possible.
-
ISN -
Com-Power Corporation
They are required for the measurement of conducted common mode noise on Telecom Cables of Information Technology Equipment (ITE). These measurements are necessary to meet the requirements specified in CISPR 22 and CISPR 32 standards.
-
Renesas Electronics Corp.
Renesas' single and dual low dropout regulators (LDO) offer ultra-high PSRR up to 3MHz, low input voltage range, tiny packages, and ultra-low noise and quiescent current.
-
Tektronix, Inc.
Optimized for power integrity measurements, these probes combine low noise contribution, DC offset up to 60 V, high bandwidth, low loading, and a wide range of connectivity alternatives.
-
8006 -
April Instrument
Normal switching mode, SSB phase noise will be degraded in the fast mode. 5 digit BCD, 1 latch control line, 25 pin female, D type connector
-
8007 -
April Instrument
Normal switching mode, SSB phase noise will be degraded in the fast mode. 5 digit BCD, 1 latch control line, 25 pin female, D type connector
-
8005 -
April Instrument
5 digit BCD, 1 latch control line, 25 pin female, D type connector. Normal switching mode, SSB phase noise will be degraded in the fast mode.
-
Laplace Instruments Ltd.
The ease and effectiveness of conducted emission measurements can be enhanced by the use of appropriate filters. In particular, broadband noise below the frequencies of interest can cause limiting (compression) in spectrum analysers, distorting the measurements.
-
Columbia Research Laboratories
The line of Biaxial Force Balance Linear Accelerometers available are 2-axis versions of our General Purpose, Low Noise and High Temperature, and High Performance Single axis Linear Accelerometers.
-
Scien Co., Ltd.
Facility fault diagnosis measuring instrument with technology that accurately tracks the heating part and abnormal noise generating part during operation of machinery using thermal imaging camera and microphone
-
AP2019 -
ZETLAB Company
*Can be used as shock sensors in equipment diagnostic systems;*Combination of high axial sensibility, intrinsic frequency and shock resistance;*Low sensitivity to electromagnetic fields;*Low intrinsic noise level.