Showing results: 1141 - 1155 of 2138 items found.
-
SL100 -
TEAM SOLUTIONS, INC.
The SL100 uses a standard 16450 UART with baud rate settings that makes it capable of communicating with a Chrysler CCD Vehicle bus. The SL100 uses a protected interface driver chip, as prescribed by the bus specification, to connect with vehicle peripherals in a robust and highly noise immune way. The card automatically configures to become another COM port by using the built-in O.S. drivers that are tried and tested and are optimized to work in the Windows environment.
-
GreenPoint® -
ON Semiconductor
The GreenPoint Design Simulation Tool is an interactive online design and verification tool to help you generate and validate an electronic design. The simulation module provides an interactive design and verification environment. The power analysis module provides an interactive environment to analyze the performance of intelligent power modules (IPMs). The Phase Noise Explorer module enables an interactive environment for advanced phase noise/jitter analysis of clock tree designs.
-
CF extend 180 -
Sycard Technology
The CF extend 180 is a flexible extender card designed to provide easy access to a CompactFlash™ card for debug or test. Designed with the same low noise characteristics of our CF extend 160, the CF Extend 180 takes this design a step further by connecting the host and card via ribbon cables. The flexible extender consists of two PC boards, the host interface board and the card interface board.
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
The piezoelectric accelerometers on this page are intended for the measurement of lowest vibrations. Typical fields of application include the monitoring of buildings, dams, bridges, oil platforms and pipelines. These sensors are often called seismic accelerometers because they are used to monitor construction activity, volcanoes and earthquakes. Their high sensitivity is achieved -unlike other high sensitivity accelerometers- by the sensing element itself and not by internal amplification. From this results highest resolution and lowest noise.
-
130A23 -
PCB Piezotronics, Inc.
Nominal Microphone Diameter: 1/4" Frequency Response Characteristic (at 0 incidence)Free-FieldInherent Noise (A Weighted)<30 dB(A) re 20 Pa<30 dB(A) re 20 Pa Dynamic Range (High)150Environmental Temperature Range ( Temperature Effect on Output (-10 to +50 C)<0.7 dB<0.7 dB[2] Influence of Axial Vibration Excitation Voltage 18 to 30 VDC18 to 30 VDC
-
2575 -
PCB Piezotronics, Inc.
Performance:Nominal Microphone Diameter1"1" Frequency Response: Characteristic (at 0 incidence) Random IncidenceRandom Incidence Open Circuit Sensitivity: 45 mV/Pa Resonant Frequency (90 Phase Shift)8000 Hz8000 Hz[1] Inherent Noise<10 dB(A) re 20 Pa<10 dBTemperature Range (Operating)TBD FTBD C Humidity Coefficient of Sensitivity (0 to 95%, non-condensing)0.001 dB/%RH
-
Silent Solutions LLC
SILENT Troubleshooting and Retrofit Service provides rapid problem resolution. We will work onsite at your facility, or if you prefer, you may ship the product to our troubleshooting lab for an immediate problem review. After seeing their design staff bogged down for weeks, our clients are delighted to see us bring a noise problem under control in a matter of days, and with practical design solutions that are manufacturable.
-
HSX SERIES -
Holzworth Instrumentation, Inc.
The HSX Series are broadband frequency sources exhibit industry leading phase noise and spectral purity performance coupled with a highly accurate dynamic range of up to +20dBm and down to -110dBm. The 1U high form factor offers 1, 2, 3 or 4 channel models; all providing the ultimate in frequency accuracy, while the phase coherent RF outputs provide the ultimate in channel-to-channel stability.
-
Integris 3000 -
Absolute Analysis
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
MGC-1 -
Macintyre Electronic Design Associa
The MGC-1 is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1 amplitude response is insensitive to the frequency of the field over its 5 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
MGC-1A -
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
CMOS Global Shutter -
Framos Technologies d.o.o.
Its outstanding performance, success, and large consumer capacity were among some of the triggers resulting in Sony’s decision to shut down their CCD sensor development and production, despite their technology and market leadership. The Pregius technology series combines the image quality from its technology with high readout speeds, an electronic global shutter and the low noise EXview HAD II Technology from the CCD designs.
-
897 -
Simpson Electric Company
Designed for conducting personal noise surveys, the 897 Dosimeter is versatile enough for the experienced hygienist but simple enough for the novice technician. The data storage feature allows you to view reports on the computer or print them for use later during inspections. Purchase the 897 by itself or in the SMS-2 kit with all of the relevant accessories, including calibrator, nose cone, microphone clip, wind screen, and serial and parallel printer cables.
-
MT310-104 -
ALTINEX, Inc.
The MT310-104 is a Balanced Stereo Audio Matrix Switching Card. This card allows any input to be independently switched to any of the outputs. Also, any input may simultaneously drive multiple outputs. All inputs and outputs can be wired for unbalanced stereo audio, or balanced audio allowing longer cable runs and superior noise resistance. Click the image below for your own copy of the MultiTasker Design Guide as a PDF.
-
OS-CON™ -
Panasonic Industrial Devices Sales Company of America
Panasonic's OS-CON™ Aluminum-Polymer Solid Capacitors are available in both surface-mount and through hole types. These Solid Electrolyte Aluminum OS-CON™ Capacitors utilize aluminum and a highly conductive polymer material to offer low ESR, excellent noise reduction and ripple current capabilities. The OS-CON Series parts are characterized by a long-life and minimal ESR changes throughout the entire product line’s rated temperature range.