Showing results: 166 - 180 of 246 items found.
-
PH-01 -
Pansco, Ltd
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
Pro-Check 725 -
LITE-CHECK LLC.
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.
-
SC-8108 -
Comunion Technology Co., Ltd.
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
-
Chroma ATE Inc.
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
JA/JP Series -
Semiconductor Circuits, Inc.
The 15-Watt JA/JP series operates over an ultra wide range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 80% are typical over varying load conditions of 25% to 100%. Additional features include input reverse polarity protection, remote on/off control, logic compatible with CMOS or open collector TTL, short circuit protection with auto restart, overvoltage protection, and an operating temperature range of -25°C to +71°C with no derating. Units are packaged in a six-sided continuous shielded case for EMI/RFI protection and measure 2.0” x 2.0” x 0.40”.
-
TA Series 25 Watt -
Semiconductor Circuits, Inc.
The 25-Watt TA series operates over an ultra wide input range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 77% are typical over varying load conditions of 25% to 100%. Additional features include input reverse polarity protection, remote on/off control, logic compatible with CMOS or open collector TTL, short circuit protection with auto restart, overvoltage protection, and an operating temperature range of -25°C to +71°C with no derating. Units are packaged in a six-sided continuous shielded case for EMI/RFI protection and measure 2.5” x 3.0” x 0.83”
-
MEATEST, s.r.o.
Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.
-
Pickering Interfaces Ltd.
Pickering's PXI precision programmable resistor modules feature high setting resolution with excellent stability and accuracy through the use of innovative switching networks and software correction techniques. This also means all resistance values can be set - there are no missing values due to switch resistance or resistor tolerance. These modules are ideal for sensor emulation applications that require very fine adjustment and also have the capability of being set as open or short circuit to simulate faults in cabling systems. The range includes modules specifically designed for RTD and strain gauge simulation.
-
50-201-004 -
Pickering Interfaces Ltd.
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
50-201-008 -
Pickering Interfaces Ltd.
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
AI-5120 -
Advent Instruments Inc.
The AI-5120 is a compact device designed for monitoring and analyzing signals present on the telephone line. By sensing the voltage present on the telephone line it detects and measures ringing, DTMF & pulse dialing, FSK (Bell 202 and V.23) signals, line polarity reversals, and open switching intervals (OSI). Working in conjunction with the TRsSim software on a PC, the AI-5120 becomes a valuable tool in analyzing and debugging Caller ID and SMS (Short Message Service) data transmission. Like an oscilloscope, it can capture and display waveforms showing various signals present on the telephone line.
-
40-262-002 -
Pickering Interfaces Ltd.
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
40-262-101 -
Pickering Interfaces Ltd.
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
40-262-102 -
Pickering Interfaces Ltd.
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
40-262-202 -
Pickering Interfaces Ltd.
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.