- Pickering Interfaces Inc.
product
Serial AC Power Sequencer
90-200-001
Each power outlet can be programmed to switched on in sequence with a specific timing delay. The delay can be staggered to ensure that order dependent systems - like PXI - can be switched on and off in an orderly way with just one operation. A staggered start up also limits the inrush current associated with the powering up of equipment, including earth current inrush, placing less stress on cabling and leakage breakers. Power on or off instructions can be initiated from either the front panel switch or via the serial interface.
-
-
-
product
Socket Outlet Tester
Using the new Testavit Schuki 1 LCD and 3 LCD, specialists easily check to see if sockets, cable drums or connecting cables are correctly connected in 230 V installations. Due to three LEDs, the connection status can be quickly and clearly determined. In addition, through the finger contact, it can be tested to see whether an impermissible, high contact voltage is applied at the protective earth connection. In addition, using the Testavit Schuki 1 LCD, a 30 mA FI circuit breaker (RCD) can be triggered via a pushbutton.
-
product
Temporary Power Outlet
K-271, K-272, and K-273
Knopp’s Temporary Power Outlets are an easy and safe solution for construction sites or other areas where power is not easily accessible. The device provides temporary electric service by isolating power from the breaker panel. Easy-to-use and versatile, Knopp’s Temporary Power Outlet eliminates the need for portable generators and can be used for motor homes, travel trailers, marine shore power, construction sites, and solar pump stations. Emergency situations such as hurricane restoration, storm outages and fire damage can also utilize this device.
-
product
Pressure Regulators & Outlet Points
WITT offers a wide range of gas pressure regulators and gas outlet points for almost all technical gases, pressure and flow requirements. Our product portfolio includes spring-loaded pressure regulators, dome-loaded pressure regulators and complete pressure regulating stations as well as outlet points and system solutions for safe and reliable gas supply.
-
product
Socket Outlet Torque Test Device
CX-LJ
Shenzhen Chuangxin Instruments Co., Ltd.
For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets, in accordance with IEC 60065 clause 15.4.1 and figure 11, IEC 60335-1 clause 22.3, IEC 60884-1 clause 14.23.2.
-
product
IEC60065 Fig11 Australia UL Plug Socket Tester Socket Outlet Torque Tester
CX-CTN
Shenzhen Chuangxin Instruments Co., Ltd.
The plug torque tester conforms to the standard of IEC60065 figure 11. It is used for checking whether the mechanical stress which occurs when the Direct Plug-in Equipment with plug pin normally insert into the socket is in the required range.
-
product
Heavy-Duty Circuit Tester With Grounding Adapters
30610
Heavy-duty circuit tester with multiple options for connecting to a ground source. Long, 12’ cord has a quick coupler to securely connect clamp or power outlet plug. Large, strong clamp connects securely. Power outlet plug can always be used to provide ground in the cabin. For testing circuits up to 12 volts.
-
product
HeNe Laser System with Built in Receiver and Power Supply
5519A
The Keysight 5519A Laser is a Helium Neon Laser (HeNe) that offers exceptional stability. The laser is a complete system with a built-in receiver and its own power supply that plugs directly into an AC power outlet.
-
product
HeNe Laser System with Built in Receiver and Power Supply
5519B
The Keysight 5519B Laser is a Helium Neon Laser (HeNe) that offers exceptional stability. The laser is a complete system with a built-in receiver and its own power supply that plugs directly into an AC power outlet.
-
product
Hose Couplings
WITT quick couplers / hose couplings SK100 for gases provide a safe, quick and distinctive connection of the hose with outlet points or working equipment.An automatic cut-off valve prevents any gas flow when disconnected. WITT hose couplings have an integrated non-return valves which prevents the formation of explosive gas mixtures in the pipeline.
-
product
HPLC Pumps
M1 Class
Applications include precise chemical metering, dispensing, and specific HPLC separations. Standard fluid path materials are Stainless Steel and PEEK. With 10 mL/min, 40 mL/min, and 100 mL/min versions, reaching pressures up to 2,500 PSI, these pumps capture the majority of typical laboratory fluid transfer applications. Features include interactive keypad control and Outlet Filter, RS-232 Serial and Micro USB 2.0 ports for complete PC control and status, as well as hardware for laboratory stand mounting. Having the smallest possible footprint for a high pressure pump, the M1 Class will easily integrate into any laboratory or industrial environment.
-
product
HVAC/R Environmental Meter
FLIR EM54
The FLIR EM54 is ideal for inspecting and troubleshooting HVAC/R ducting systems within residential, commercial, and industrial facilities. This meter can help you verify that duct inlets and outlets have the specified volumetric flow – a prerequisite to an efficient functional system. Featuring humidity, wet bulb, and dew point functions, the EM54 can measure deviations from proper relative humidity levels. Plus, the included Type-K contact temperature probe is useful to check electric motors and thermal equipment components for proper operating temperatures.
-
product
Hydraulic Hand Pumps
AMETEK Sensors, Test & Calibration
Our high-pressure, hydraulic hand pump provides a compact pressure source for any environment and works with petroleum-based oils and hydraulic fluids. Three different models are available to produce up to 5000 psi / 300 bar, with two outlet ports, large reservoir, and an easy-to-use fine adjust. Each pump is available on its own, or in one of our complete ready-to-use pump systems.
-
product
Input Digital Temperature Transmitter
HR6100
HighReach Measuring & Controlling System Co.,Ltd
The HR6100 input-type integrated temperature transmitter uses an imported temperature sensor to transmit and output RS485 standard signals through a built-in microprocessor. The product adopts the sealing structure of the liquid level transmitter, the waterproof cable outlet, the 316L stainless steel casing, And the temperature probe to the front end, which is suitable for occasions with special requirements on the installation dimensions.
-
product
IT Infrastructure, Asset And Connectivity Management System
CableSolve is an enterprise ready Connectivity and Infrastructure Management System that provides portable and end-to end management, and documentation of the IT infrastructure and network connectivity. Manage your entire physical infrastructure from the structured cabling to the switches, routers, and PABX’s all the way to the outlets, desktop PCs and telephones. The desktop component provides end-to-end management, reporting and control while providing portable management of the connectivity infrastructure with the use of one or more Pocket PCs with integrated barcode scanner for extra mobility and flexibility.
-
product
IT Infrastructure, Asset And Connectivity Management System
CableSolve is an enterprise ready Connectivity and Infrastructure Management System that provides portable and end-to end management, and documentation of the IT infrastructure and network connectivity. Manage your entire physical infrastructure from the structured cabling to the switches, routers, and PABX’s all the way to the outlets, desktop PCs and telephones. The desktop component provides end-to-end management, reporting and control while providing portable management of the connectivity infrastructure with the use of one or more Pocket PCs with integrated barcode scanner for extra mobility and flexibility.
-
product
LAN Cable Tester Plus
PK-3456 Spy Splitpair
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
product
LCD Display Battery Monitor
TE6-0609
Hangzhou Tonny Electric & Tools Co., Ltd.
*Plug into a standard 12V/24V power outlet*Two USB outlets for charging 1x standard 1A and 1xhigh *output 2.4A*Voltage is displayed by digital read out to indicate battery*charge level*Flashing LED alarm and warning audible sounder indicates*low battery voltage*Replaceable 3A fuse*Suitable for 12V negative earth systems*Adjustable main plug angle*Ideal for the vehicle that double as a mobile office
-
product
Multi Jet Meters
The water enters the meter from the inlet of the meter body and impacts the vane wheel at the tip of the vane blades to make it rotate. The water flows out from the outlet of the body. The rotation of the vane wheel (proportional to the velocity of water flow) is transmitted directly to the central gear in the vacuum-sealed register by the magnetic coupling. The sealed register totalizes and indicates the water volume passing through the meter.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the...show more -
product
Non Contact Detectors
*Adjustable to safely detect power and low voltage*Safely detects AC voltage without touching the bare conductor*Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits*Use to detect voltage in outlets, lighting fixtures, wires and cables*Finds breaks in wires*Identifies hot and neutral conductors*Low battery indication
-
product
Non-contact High Voltage Testing
Shanghai Beha Electronics Co., Ltd.
An ideal tool for checking the presence of AC high voltages and AC low voltages in cables, wall outlet, fuses......etc.
-
product
Non-Contact Voltage Tester
1AC II
The portable 1AC II non-contact voltage tester from Fluke are easy to use – just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home and even detect miswires of an electrical outlet.
-
product
Non-Contact Voltage Tester
NCVT-1
Non-contact detection of voltage in cables, cords, circuit breakers, lighting fixtures, switches, outlets, and wires.High intensity, bright green LED indicates the tester is operational and aids in illuminating the workspace.When voltage is detected, a high intensity, bright red LED illuminates and a warning tone sounds.Discrete digitally controlled ON/OFF power button.Auto power-off feature conserves and extends battery life.Microprocessor controlled low-battery indicator and tester shutdown.CAT IV 1000 Volt safety rating provides expanded operation and protection.
-
product
Non-Contact Voltage Tester
1LAC II
The Fluke 1LAC II Non-Contact Voltage Tester is easy to use – just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home.
-
product
Non-Contact Voltage Tester
2AC
The Fluke 2AC is the latest addition to the VoltAlert™ AC non-contact voltage tester family. It is designed to be pocket-sized and easy to use. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip, or power cord where voltage is present. The 2 AC is always on, with a battery check function to make sure the tester is working properly.
-
product
Non-Contact Voltage Testers
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
product
Non-metallic Pipe Locator
NPL-100
The NPL-100 is a sophisticated instrument for locating non-metallic water pipelines.Using a vibrator attached to the outlet of a fire hydrant or to pipe fittings, the NPL-100 sends a sound wave through the water in the pipe.
-
product
Non-Return Valves / Check Valves
WITT gas non-return valves (Check valves) are used to protect plants, piping systems and outlet points against dangerous gas backflow and unwanted gas mixtures. Key features of WITT’s unique design are their very low opening pressures and very low pressure drop, so they are particularly suited to low operating pressure applications.
