Showing results: 361 - 375 of 628 items found.
-
V-M.O.L.E.® -
E.C.D.
The V-M.O.L.E. is a full-featured compact thermal profiler that belies its sophistication in an easy-to-use 3-channel Mini-thermocouple configuration. Ideal for VERIFICATION of PCB profile performance, 3 channels give you Hot, Cold and Sensitive component data for verifying the correct oven settings.
-
Ironwood Electronics
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
Series 67 & 68 -
Pickering Electronics
Series 67 PCB mounting with switch and coil connections in a Single-in-Line format.Series 68 PCB connections on the underside for coil connections. Flying leads from the top face for high voltage connections.The Series 67 and 68 are constructed using former-less coils. The absence of a coil supporting bobbin allows a device smaller than the industry norm. The unusual package design gives some interesting possibilities for high density packing.The option of flying leads for the high voltage connections makes it possible to keep this away from lower voltage circuitry on the pcb.Form A (energize to make) contacts are available with the option of 5, 12 and 24 volt operating coils.
-
SEM1550 Series EDFA Module -
Hangzhou Softel Optic Co., Ltd.
*Adopts JDSU or Oclaro pump laser.*Adopts OFS fiber.*SMT production process to assure small size and low power consumption ,but high stability*Micro monitor PCB*Output adjustable(-4~+0.5)*Max outputs 23dBm(single pump laser).
-
C500RMX-4SB-1B -
Pickering Interfaces Ltd.
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector.
-
C500RMR-4SB-1B -
Pickering Interfaces Ltd.
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector.
-
Qorvo
Qorvo's variable gain amplifiers (VGAs) integrate high-performance amplifier solutions along with digital or analog gain control. Several of our VGAs integrate all of the RF matching and bias circuitry into a single package, providing a very compact solution and reducing PCB space.
-
HF-960M -
HORIBA, Ltd.
The HF-960M uses sensors that offer outstanding corrosion resistance for high-precision, high-speed measurement of low concentrations of hydrofluoric acid, hydrochloric acid and ammonia, and is thus perfect for single-bath and wafer cleaning. The HF-960M is also an environmentally-friendly product that uses lead-free solder for mounting chips on the PCB.
-
PRO RACK ATE -
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
Amphenol RF
Amphenol RF offers a full range of RF connectors designed for use in a variety of applications and markets. Cable mount, PCB mount and Board-to-Board solutions are available. Other features include non-magnetic, IP rated sealed and isolated connectors. Custom products can also be developed.
-
8376 -
SparkFun Electronics
A very simple breadboard power supply kit that takes power from any USB port and outputs a fuse protected and regulated 3.3V. The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled 5V/GND 3.3V/GND plug directly into the power lines.
-
Series 647 -
Aries
Universal SOIC to .600 [15.24] DIP Adapter. 44 pin adapter for mounting Aries Series 547 Universal SOIC ZIF (zero insertion force) Test Socket to .600 [15.24] DIP PCB layout. Consult Data Sheet No. 10015 for test socket information.
-
Series X55X -
Aries
Universal Zero Insertion Force DIP Test Socket. All pin count sockets go into PCB with either .300 or .600 [7.62 to 15.24] centers. Sockets can be soldered into PCBs or plugged into any socket. Socket fits into Aries or any competitive test socket receptacle.
-
BMP180 -
Adafruit
This precision sensor from Bosch is the best low-cost sensing solution for measuring barometric pressure and temperature. Because pressure changes with altitude you can also use it as an altimeter! The sensor is soldered onto a PCB with a 3.3V regulator, I2C level shifter and pull-up resistors on the I2C pins.
-
KY8030-3 -
Koh Young Technology
The new KY8030-3 delivers 3x fasterinspection without compromisingperformance and accuracy.Using patented dual projection,the system eliminates the criticalShadow problem that all 3D SPI systemscan be vulnerable to.Additionally, the new KY8030-3 has solvedthe PCB Warp problem that seriouslyimpacts inspection accuracyand reliability of result.