Showing results: 331 - 342 of 342 items found.
-
Advantech Co. Ltd.
PCI/PCIe-bus non-isolated digital I/O cards for parallel data transfer, TTL DIO, and logic signal sensing.
-
Dynamic Engineering
IndustryPack compatible IP-Parallel-IO with counter and timer design adds up to 48 digital parallel IO lines to one IP slot of your carrier board.
-
Advantech Co. Ltd.
PCI-bus non-isolated digital I/O cards for parallel data transfer, TTL DIO, DTL and CMOS DIO logic signal sensing.
-
DIO2 -
APPLICOS
The DIO-II module is a multimode digital source and capture unit. In Low Speed Mode it provides a 20-bit parallel or 24-bit serial I/O capability running at speeds up to 50 MHz. In High Speed Mode, the DIO-II provides a 16-bit parallel I/O capability up to 200 MHz. In both Modes, the Clock is generated by a low jitter PLL source that is capable of generating clocks from 320 kHz up to 1 GHz.
-
104-DIO-48S -
Acces I/O Products, Inc.
*48 or 24 parallel lines of 82C55 digital I/O with tristate buffers prevent unintended control of external equipment*IRQ on input change of state (COS) eliminates the need for constant polling*High sink/source current 64mA/32mA*I/O pulled up to 5V for contact monitoring*Compatible with Opto-22 and other industry standard I/O racks
-
Dynamic Engineering
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
PCI-DIO-24D/H -
Acces I/O Products, Inc.
These cards are 24-bit parallel, digital input/output cards designed for use in PCI-Bus computers. The difference between the models is that I/O connections to PCI-DIO24D are via a standard 37-pin D-sub connector while I/O connections to PCI-DIO24H are via a 50-pin connector. The cards are 4.80 inches long (122 mm) and may be installed in any 5V PCI-bus slot in IBM and compatible personal computers.
-
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters. In deployed systems, an FPGA's technical advantage translates to smaller, lower power, and lower cost systems. Our commercial off-the-shelf (COTS) 3U VPX FPGA cards include a wide complement of I/O functionality and are engineered to succeed in the most demanding rugged applications.
-
FOX-XP -
Aehr Test Systems
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters. In deployed systems, an FPGA's technical advantage translates to smaller, lower power, and lower-cost systems. Our COTS 6U VPX FPGA cards include multiple FPGAs, a wide complement of I/O functionality and are engineered to succeed in the most demanding applications. When supercomputing processing performance is required, HPEC systems meet the most demanding rugged deployed application needs by combining the highest performance FPGAs, GPGPUs, processors, and networking modules available.
-
NI
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
ICS Electronics
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
