Showing results: 841 - 850 of 850 items found.
-
T3DSO1000 Series -
Teledyne LeCroy
Teledyne Test Tools new T3DSO1000 Oscilloscopes feature two channel and four channel models. The two channel model is available with 100 MHz, a single ADC with a 1 GSa/s maximum sample rate, and a single memory module with 14 Mpts of sample memory. The four channel scope is available in 100 and 200 MHz models and incorporates two 1 GSa/s ADCs and two 14 Mpts memory modules. When all channels are enabled, each channel has sample rate of 500 MSa/s and a standard record length of 7 Mpts. When only a single channel per ADC is active, the maximum sample rate is 1 GSa/s and the maximum record length is 14 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
GX5295 -
Terotest Systems Ltd.
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
GX5296 -
Terotest Systems Ltd.
The GX5296 offers the most performance and features of any 3U PXI dynamic digital I/O board on the market today. The 32-channel, GX5296 offers timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability emulate and test complex digital busses for system, board or device test applications. Offering 1 ns edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level).
-
410112664 -
Virginia Panel Corporation
This aluminum enclosure is for ITA Part # 410 120 111 and allows your 18 Module Solution to be customized to your needs. This enclosure has three U-shaped cable clamps that allow a maximum cable bundle of 1.59sq. in. per clamp. ITA strain relief plates are not needed.
-
-
SLAMMO -
Creative Lighting
When it comes to LED control, bigger IS better and the SLAMMO boasts class-leading capacity of up to 25Amps, 600W @24VDC (up to 450W in IP67 enclosures) / 300W at 12VDC. For constant current LEDs, the SLAMMO P can drive up to 96 luminaires equipped with PWM controlled CC drivers such as the Meanwell LDD series (350mA to 1.6A per LDD)
-
CX-500 -
Shenzhen Chuangxin Instruments Co., Ltd.
Test Sphere Probe This sphere is intended to verify the degree of protection of enclosures for an IP2 Code per IEC 529. Sphere is hardened steel with chrome finish. TOP
-
410114138 -
Virginia Panel Corporation
This aluminum enclosure is for ITA Part # 410104375 and allows your 10 Module Solution to be customized to your needs. This enclosure has three U-shaped cable clamps that allow a maximum cable bundle of 1.59sq. in. per clamp. ITA strain relief plates are not needed.
-
410 -
Elcometer Limited
Rugged and durable: the Elcometer Anemometer is made from high impact injection moulded plastic and corrosion resistant materials.Waterproof: Waterproof equivalent to IP67 with fully sealed electronics. Will also floatin water if dropped.Clear LCD Display: Easy to read, large 9mm digits.Choice of measurement units:Beaufort ForceKnotsKilometres per hourMetres per secondMiles per hourFeet per minute
-
Elcometer Limited
To maintain consistency of a coating, the Density should remain constant from batch to batch. Density Cups, also known as Specific Gravity Cups or Picnometers, are used to determine the mass per unit volume (Specific Gravity) of a liquid at a given temperature. Specific Gravity is defined as the ratio of the density of a given substance to the density of water, when both are at the same temperature. As the Specific Gravity Cup is an exact measurement of the volume of the liquid, it is imperative that the exact weight of the sample is obtained.