Showing results: 406 - 420 of 726 items found.
-
Praxsym
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
PSG-300 -
FRANKONIA GmbH
The PSG-300 contains a linear precision power amplifier with a wide bandwidth (DC-300 kHz), suitable for all applications concerningfast alternating signals at high output power. The built in generator provides sine, square and triangle waves.
-
Op Amp Series -
Texas Instruments
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
Insight Product Company
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Keysight Technologies
Instead of cascading a set of narrowband amps, use a single amplifier from Keysight and enjoy ultrabroad bandwidths - like 0.01 to 26.5 GHz, 0.045 to 50 GHz, and ranges in between. But the best thing about Keysight broadband amplifiers is what they eliminate and reduce: noise, crossover networks, and multiple power supplies.
-
Cohu, Inc.
PAx semiconductor test system delivers uncompromised RF performance in a low-cost system for testing RF power amplifiers and front-end modules for next-generation wireless standards.
-
1147B -
Keysight Technologies
The 1147B is ideal for capturing transient current signals such as those found in motor controllers, switching power supplies, inverters and current amplifiers driving inductive loads.
-
Kuhne electronic GmbH
Kuhne electronic Signal Generators are available in the following variations:RF Generator as Compact Module in the form factor of a power amplifier (frequency and power can be adjusted)Laboratory Instrument for immediate use with self-explaining user interface for adjustment of frequency and power as well as multiple monitor information possibilities
-
HA5100 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
PGY-RFFE-EX-PD -
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
PAS 9818/AO -
Precision Analog Systems Co.
The PAS 9818/AO provides eight programmable current output channels with sixteen bit resolution on a 6U VME card. Each channel consists of a high speed Digital-to-Analog Converter (DAC), followed by a high power operational amplifier. The output amplifier is configured to provide an output current that is proportional to the output voltage from the DAC.
-
CMS 356 -
OMICRON electronics
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
Ponovo Power Co., Ltd.
In the PHIL (Power Hardware In-Loop) Case Study, the PHIL system consists of a PONOVO 4-Q amplifier, RTDS simulator, DC electronic load unit and PV inverter.
-
Teledyne e2v
We are market leaders in the design, development and manufacture of helix travelling wave tubes (TWTs), travelling wave tube amplifiers (TWTAs) and microwave power modules (MPMs).
-
Macom Technology Solutions Holdings Inc.
MACOM’s FTTx amplifiers are designed for PON, RFoG and SFU receiver equipment and are offered in small, plastic QFN packages with integrated amplifier and attenuator functions. All parts cover the full 45 to 1000MHz / 1200MHz CATV band. 5v and 12v solutions are offered with power consumption of ≤ 1.5Watts. MACOM’s FTTx amplifiers are characterized with industry standard photodiodes, covering optical input ranges from -12 to +3dBm and each sample EVK comes complete with a photodiode and APC connector.