Showing results: 1921 - 1935 of 2950 items found.
-
XG-8000 series -
Keyence
Offering a lineup of up to 21 megapixel area cameras and 8K line scan cameras, the XG Series contains powerful vision system technology providing flexibility and power to solve a wide range of applications. No experience required to select lighing! - newly-developed, revolutionary Lumitrax function. Powerful Vision Software. Flexible Multi-Camera Hardware.
-
CMS 356 -
OMICRON electronics
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
Maury Microwave Corporation
Manual tuners are used both in the laboratory and as system components to establish or transform impedances for a number of applications. They can be used to establish optimum source or load terminations for device characterization, normalize a source or load for precision laboratory measurements and/or calibrations (noise, power, etc.), and can act as a matching transformer between a mismatched source and a mismatched load.
-
PR0128 -
PREMOSYS GmbH
The CIELab Color Sensor PR0128 is a color detection system with integrated high power light source, for determining the surface color. It is characterized by the identification of the smallest color nuances and the highest long-term stability. Here, up to 63 completely different products in different colors can be independently controlled and tested without changing parameters or gain levels.
-
CXAR/32-MF -
Cytec Corp.
These Chassis controls up to four 8x1 modules, eight 4x1 modules or mixtures of 8x1's, 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system. Pushbutton manual control is optional.
-
CXAR/16-MF -
Cytec Corp.
These Chassis controls up to two 8x1 modules, four 4x1 modules or mixtures of 8x1's, 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system. Pushbutton Manual control is optional.
-
YHS-2 -
Wuhan Sangao Electrical Test Installations Limit Co.
Water in oil transmitter is used for monitoring of Monitoring of hydropower, thermal power plants and large pumping oil system's moisture content. When the oil tank, oil pipe water content exceeds the alarm settings, alarm signal to remind the staff on duty, timely inspection system, to ensure the safe operation of generating units.
-
Kontron
Hartmann Electronic’s 17 slot 19” rack mountable VME solution – The VME64x 7U system. This VME chassis comes with two 400W cPCI hot-swap power supplies with vertically oriented card slots. This platform conforms to VITA 1.1-1997 while providing a high capacity yet practical packaging solution for high-performance processors.
-
BKP3-CEN08-15.2.15-4 -
Kontron
This 8 slot Hartmann Open VPX BKP3-CEN08-15.2.15-4 profile system chassis provides an intelligent, practical packaging solution for high-performance processors. The 84HP wide, rack-mountable enclosure for vertical mounting of boards is outfitted with either a 600W ATX or 600W plug-in VPX power supply and a 1U removable, bottom mount fan tray.
-
ENDA-5000 series -
HORIBA, Ltd.
Continuous simultaneous and high-precision measurement of NOx, SO2, CO, CO2 and O2.HORIBA has over 100,000 CEM systems installed and 30 years of quality and experience. That is the base on which HORIBA's new ENDA-5000 series of stack-gas analysis systems are built. These systems have a small footprint and use cross-flow modulated non-dispersive infrared (NDIR) and magneto-pneumatic detectors that are inherently drift-free. The ENDA-5000 series are superior continuous analysis systems that perform reliably for difficult exhaust gas measurements, when measurement errors cannot be tolerated. This CEM series features a new intuitive touch panel that makes every operation available with the touch of a single button. The ENDA-5000 series systems are also designed for ease of maintenance. They are ideal for a variety of uses, including emissions monitoring from steam boilers, refuse incinerators, and electric power generation plants to assure pollution standards are being met.
-
WISER 4000 -
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
MEMRECAM Q1 Series -
nac Image Technology Inc.
*The MEMRECAM Q1 Series cameras can operate as single stand alone cameras, or in a synchronized multi-camera system*Compact, rugged design – can withstand 150G shock for 10ms*Built-in Memory Backup is a standard feature (Up to 1 hour)*2/3-inch format supports standard C-mount and custom Hi-G lenses*62 (H) x 62 (W) x 65mm (D) , 400g.*Fully integratable with existing GX and HX Cameras*Supports simultaneous download of multiple MEMRECAM cameras*Power Input: 20-32 VDC*Power Consumption: 20W
-
PDMonitor -
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Badger Meter
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
Compact Series -
Seek Thermal
Made for iPhone® and Android™ top models, Seek Compact transforms your smartphone or tablet into a professional thermal imaging tool. By utilizing the power and convenience of your smartphone, our cameras make it easy to take thermal photos and video, share findings, and send for documentation. Simply connect and detect energy loss caused by air leaks, missing or damaged insulation, inefficient HVAC systems, electrical faults, and much more. On top of all this, Seek Compact cameras are engineered to run on low power from your smartphone and do not require batteries or