Showing results: 4891 - 4905 of 11103 items found.
-
QST-5 -
DeltaTech Electronics
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
AFL
Is to inject a known level of light in one end and measure the level of light at the other end, using an OLTS. The difference between source and receive power levels is the loss.
-
NC3400 -
Noisecom
The NC3400 Series coaxial noise sources are an excellent choice for applications requiring high ENR and immunity to large incident RF power, such as ATE, radiometer, and radar systems
-
TA-60 -
Tech-Aid Products
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
YAV90090 -
6TL Engineering
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
Model KM-MPS-50K -
Kusam Electrical Industries Limited
• AC 50kV and DC 50kV measurement with direct reading.• 4000-count LCD.• Input impedance : 400 Mohm• Auto-ranging : AC : 4.000kV / 40.00kV / 50.0kV, DC : 4.000kV / 40.00kV / 50.0kV• KM 50K must be connected with an approved hot stick (Optional).• Check phases are "in-phase" or "out of phase".• Polarity indication : Positive / Negative• Backlight function.• Auto power off.• Power source : 1.5V(AA) alkaline battery × 2.• Low battery indication(Multi-level).
-
MT7553 Series -
Maury Microwave Corporation
Noise Parameters are the non-50Ω extensions of Noise Figure, and are an important modeling and model validation tool to understand how a device-undertest’s performance changes as a function of source impedance. Noise Parameter measurements are typically performedusing a Vector Network Analyzer (VNA) to measure the S-Parameters of the DUT, and a Noise Analyzer (either Noise Figure Analyzer NFA or Spectrum Analyzer SA) to measure the noise power of the DUT. Noise parameters are calculated from a combination of knownsource impedances, S-parameters and noise powers.
-
TBS2000B -
Tektronix, Inc.
The TBS2000B is one of the most versatile scopes in its class, providing measurement insights for today’s leading applications, including embedded design, power supply measurement and power management analysis, education and classroom/lab instruction, and more. As a valuable tool for educators, the TBS2000B enables instructional professionals to devote more time to teaching engineering students and less time to laboratory and instrument setup. It’s the perfect complement to today’s engineering bench: versatility, accuracy, and priced at an affordable value.
-
Cleverscope Ltd.
Cleverscope Windows Application Software. Note we have added the Frequency Response Analyser (FRA) and Streaming capability to our Cleverscope application and so now it is available with all variants of our products, including units you have already bought. For power supply and power plane measurements you do need the isolated CS701 signal generator.We also now have the CS448 with four 1kV isolated channels with CMRR > 100 dB at 50 MHz.
-
DeltaTRAK
The Temperature/Humidity/Dew Point Circular Chart Recorder uses a red pen to track temperature and a blue pen to track humidity, permanently recording these measurements on a 6-inch (165mm) diameter paper chart. Power is supplied to the temperature recorder through a 110V AC 50/60 Hz plug-in adapter for Model 14013 and a 220V AC adapter for Model 14014. External power may be supplied from any 12V DC source such as automotive, marine or other battery.
-
UI9610 -
Lisun Electronics Inc.
MOS with superior performance has now been widely used in electronic ballasts, energy-saving lamps were. But power MOS test screening, matching problem. It is difficult due to a lack of corresponding inspection means that many enterprises do not have to engage seriously in quality control as well as the effect of product consistence and reliability. The equipment in a unique program designed to solve the power MOS test problem containing micro-processing, intelligent a few significant simple application.
-
H9122LG -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9122LG, operating bandwidth of 47~ 862MHz, is a suitable digital television FTTH applications, ultra-low optical receiver, Whether the machine is used analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index.. Due to the built-in optical AGC, at high optical power receiver, played limiting output, so H9122LG in the received optical power over a large dynamic range of +2 dBm ~-21dBm, and have excellent properties.
-
H9222LG -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H9222LG, operating bandwidth of 47~862MHz, is a suitable digital television FTTH applications, ultra-low optical receiver, Whether the machine is used analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index.. Due to the built-in optical AGC, at high optical power receiver, played limiting output, so H9222LG in the received optical power over a large dynamic range of +2 dBm ~-21dBm, and have excellent properties.
-
AACE Industries
The 4-Way Antenna Splitter provides a convenient means of driving multiple (up to four) GPS or GPS/GLONASS receivers off of one antenna output. The unit has a single TNC female input connector and four isolated TNC female output connectors. Power (12 VDC) is present at the TNC input connector to power an active antenna. The output ports incorporate DC blocking capacitors to allow direct connection to receivers with DC voltage present on their input connectors.
-
PSELab -
Power Spectrum Estimation Laboratory
"PSE Lab" is a freeware Windows application useful to estimate power spectrum and time frequency distribution of signals. To estimate power spectrum, the application uses following methods: periodogram; using the simplex algorithm to estimation of complex exponential model optimal parameters; using the quasi-Newton algorithm to estimation of complex exponential model optimal parameters; least squares Prony method; modified least squares Prony method; Burg method; modified covariance method; MUSIC..