Showing results: 7741 - 7755 of 11085 items found.
-
6TL Engineering
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
-
SY8125 -
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. ● The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception.● The device has the features of high stability, good reliability and large output power. ● High level of autoimmunization. The coexistence of special small keyboard and PCs, convenience to use.
-
PAS-F -
Intepro Systems
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
Peritec Corp.
Peritec Ultra Multi-Channel Battery Emulator is used for the development of electric car(EV). The hardware has great extendability, it can also simulates up to 192ch synchronized DC power supply with high isolation and you can make the test sequence with Mirosoft Excel.It can be used as a power source such as a simulator of new energy development for the evaluation. In addition, we can correspond flexibly to customize provide the best solution to suit the needs of our customers.
-
K-1000 Resistive & Inductive -
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
AR RF/Microwave Instrumentation
If you are tired of mixing and matching various components, try AR’s complete line of RF Conducted Immunity Test Systems. We now make one fully configured and standalone CI System from 4 kHz to 400 MHz with output powers designed to meet the latest commercial, custom, and military standards. In addition, AR provides configurable systems meeting your specific requirements of increased power and frequency range.
-
WTEM-2Q -
Langeo Co., Ltd.
WTEM-2Q time domain shallow TEM system is one of our latest researchers, with all functions and advantages of domestic and oversea shallow transient electromagnetic survey systems, integrated with WTEM-1J/GPS TEM system receiver and WTEM-1X low-power transmitter. It features high transmitting power, short turn-off time, high reliability, strong anti-interference performance (atmospherics, 50Hz or 60Hz industrial frequency interference), lightweight and low power consumption.
-
Kuhne electronic GmbH
. Internal filters provide high spurious rejection and image rejection. Due to low phase noise and high frequency stability of the local oscillator at 3000 MHz, the up converter is suitable for analog and digital communication systems.Typical applications are Multichannel Multipoint Distribution Systems (MMDS) using QPSK modulation and DVB?T or DVB?S systems. The output power of 20 mW can be increased to several watts by the use of an additional power amplifier.
-
LS-45-DB -
Lumistar Inc.
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
TP450-250XM-W5 -
TEAM SOLUTIONS, INC.
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
TP450-50XM-W5 -
TEAM SOLUTIONS, INC.
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
IS-*MA**P/IS-*MA**C -
Lisun Electronics Inc.
According to IES LM-79 Clause 9.1.2, it request the 4π geometry configuration and 2π geometry Integrating Sphere for the LED Testing. Lisun Group developed the integrating sphere with side assistant Opening in A Molding Technology to meet the requirements.• Painting material of integrating spheres is according to CIE Pub.No.84 (1989) • The painting material is BaSO4 coating: ρ (λ) ≥0.96 (450nm~800nm) and ρ (λ) ≥0.92 (380nm~450nm) • Fine diffuse reflection: Reflectance ρ≈0.8 and accuracy of ρ (λ) <1.5% • Build-in all functional lamp testing jigs: the vertical is for E40/E27, the horizontal is for T5/T8/T12 tubes and the Testing Holder Base for LED street luminiares. All of the testing jigs can allow the lamp be tested up and down in the sphere. • Power Cable, Power Terminal and Auxiliary lamp position has been built-in (Auxiliary lamp is option). • Two photo detector ports, one optical fiber port and temperature sensor hole are built-in • Ordering Code: IS-1.5MA55P or IS-1.5MA55C (Φ1.5m, IS-1.5MA55P means square side opening is 0.5×0.5m, IS-1.5MA55C means cycle side opening diameter is 0.5m). IS-1.75MA66P or IS-1.75M66C (Φ1.75m and side opening is 0.6m). IS-2.0MA77P or IS-2.0MA77C (Φ2.0m and side opening is 0.7m). • Other size such as diameter 2.5m, 3.0m can be special order according to customer’s request
-
MIC-3329 -
Advantech Co. Ltd.
The Advantech MIC-3329 is based on Intel® Atom™ technology, previously codenamed Baytrail and is designed to provide balanced performance and power efficiency. The MIC-3329 is a 3U CompactPCI® processor blade designed for dual-core Intel® Atom E3826/E3827 and quad-core Intel® Atom E3845 processors, and up to 4GB soldered DDR3L-1066/1333 ECC memory. It is available in single and dual slot form factor, offering a range of I/O functionality by XTM (8HP) & Rear I/O extensions. Front panel I/O on the single slot (4HP) provides 2 x RJ45 GbE ports (Switchable with RIO 4HP),1 x VGA port (Switchable with RIO 4HP), 1 x USB2.0 port and 1 x USB3.0 port. Front panel I/O on the second layer (XTM) provides 2 x COM ports (RS232/422/485), 1 x PS/2 KB/MS and 1 x Audio ports or 2 x M12 GbE ports, 1 x COM ports (RS232/422/485). The MIC-3329 provides an ideal solution for transportation, railway and factory automation applications. Its robust design from a layout and thermals perspective allows it to meet or exceed EN50155 and EN50121-4 using a very low TDP selection of 7W/8W/10W processors. Its low power consumption and industrial SoC features make the MIC-3329 a perfect fit for all fanless system applications.
-
Cohu, Inc.
PAx semiconductor test system delivers uncompromised RF performance in a low-cost system for testing RF power amplifiers and front-end modules for next-generation wireless standards.
-
TP0620 -
LEMSYS
The portable tester TP0620 is designed for easy and fast functional control of the major power semiconductors in the lab or on site (IGBT, MOSFET, diodes, thyristors and other components).
