Showing results: 8536 - 8550 of 11167 items found.
-
80952-602-6600 -
ELMA Electronic, Inc.
6U CompactPCI Backplane x-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0, clock frequency 66MHz, V(I/O) +3.3V, bus width 64-bit, power input connection with Fastons connectors
-
80952-602-6610 -
ELMA Electronic, Inc.
6U CompactPCI Backplane 2-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0, clock frequency 66MHz, V(I/O) +3.3V, bus width 32-bit, power input connection with Fastons connectors
-
MOTOMEA
The MOTOMEA Electric Powertrain Dynamometer is part of a fully integrated modular system with hardware-in-the-loop testing. System capabilities include drive cycle and virtual test driving. Powertrain testing capabilities also include battery testing and simulation using bidirectional DC power supply.
-
KM 6503 -
Kusam Electrical Industries Limited
• Temperature Range : -50°C ~ +300°C (-58°F ~ +572°F)• Temperature unit °C / °F changeable.• Data Hold Function• Power Supply : 1.5V x 1 button cell Battery.• Accessories : User Manual, Battery & Plastic tube packing
-
80942-602-6610 -
ELMA Electronic, Inc.
3U CompactPCI Backplane 2-slot, PICMG 2.0 R3.0, system slot right, supports full hot swap function according to PICMG 2.1 R2.0, clock frequency 66MHz, V(I/O) +3.3V, bus width 32-bit, power input connection with Fastons connectors
-
046-712 -
ELMA Electronic, Inc.
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane. With two coding switches on the front panel it is possible to set a constant current or load profile for +5V and +3,3V. For +12V and -12V the current will be set with two jumpers on the board.
-
056-169 -
ELMA Electronic, Inc.
The 6U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane. With two coding switches on the front panel it is possible to set a constant current or load profile for +5V and +3,3V. For +12V and -12V the current will be set with two jumpers on the board.
-
1OVX312VZK-1X11 -
ELMA Electronic, Inc.
This 14 slot 3U OpenVPX backplane (12 payload +2 power supply slots) supports high speed signals on all data paths plus has VITA67.3 modular connectors compatible with legacy VITA 67.1 and VITA 66.4 RF and optical I/O connectors.
-
LI-1500 -
Li-Cor Environmental, Inc.
The LI-1500 connects up to three light sensors with BNC terminals. Package includes four AA batteries, USB cable, AC power supply adapter, carabiner clip, carrying case, Windows® file viewer software, and instruction manual. Sensors sold separately.
-
Mors Smitt Group
NIF (Dutch Instrument Factory, later Nieaf-Smitt) started in 1900 as one of the first organizations in the world with the design and production of instruments for electrical values. The portfolio of test tools, digital multimeters, current clamps, device testers, installation testers and power analyzers is characterized by quality and reliability.
-
MS 1802 -
Meltronics Systemtech
*Bus Interface - PCI Bus*Number of Channels 198*Compatibility - TTL*Power on state - Inputs (high-Z), pulled up or down (jumper selectable)*Handshaking - Input, Output, or bi-directional*Data transfers - Interrupts, programmed I/O*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
QT-8000 Series -
PowerTECH Co,Ltd.
Tester is applicable to regularDC/AC parameter testing and IC device performance testing. Main application: Power Management; Digital Consumer Products; Communication& Interface; Automotive; Energy Conservation electronics; Standard Linear Circuit; Memory; CPU Chips; Special Customized IC and Wafer Test.
-
MODEL DPM-3 -
Transducer Techniques, Inc
The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.
-
ICS Electronics
ICS's Ethernet Parallel Digital Interface boards provide the user with a wide range of IO signals that can be user configured to match virtually any application. These Ethernet boards are available with high power relay driver boards and with optional firmware designed to simplify switching applications. The 80x3 boards have high-power TTL signals that can sink 48 mA and source 24 mA. Pullup resistors make it easy to interface with CMOS logic and to sense contact closures. User configures data byte direction and polarity. The 80x3 boards are VXI-11 compliant for operation with NI or Agilent VISA, LabVIEW and VEE and support raw socket connections. The new 8113 board is a CMOS close of the 8013 board with user set 3.3 or 5 V logic levels. Pinouts and command set is the same as the 8013 board. The 8113 communicates with TCP/IP(Raw Socket) protocoland and also has a RS-232 Serrial Port. All boards are designed for mounting against the rear panel or inside a chassis and use our Ethernet Wiring Kit for easy connection to a Ethernet Connector on the rear panel.
-
MODEL LCA-9PC -
Transducer Techniques, Inc
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.