Filter Results By:
Products
Applications
Manufacturers
Probe Systems
use programmable motorized staging to position contacting pin s.
See Also: Probe Stations, Flying Probes
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
ESS Performance Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
product
BMS Manufacturing Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
product
PXIe System Sync Module, 5 Port
M9033A
The M9033A PXIe System Synchronization Module is a dual-slot, 5-port module that provides multi-module and multi-chassis synchronization and triggering for Keysight's modular instruments.
-
product
PXIe System Sync Module, 2 Port
M9032A
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Data Acquisition System
Pixie-16
The Pixie-16 is a data acquisition system for nuclear physics and other applications requiring coincident radiation detection with large number of channels.
-
product
Scanning Electrochemical Microscope
VS-SECM (DC And AC)
The SECM integrates a positioning system, a bipotentiostat, and an ultramicroelectrode probe or tip. The positioning system moves the probe close to the surface of the sample, within the local imaging zone. The bipotentiostat can polarize the probe only (feedback mode) or the sample and the probe independently (generator-collector mode), while measuring the resulting current(s). The probe is specially designed to have a specific tapered polish (per the RG ratio) and active radius below 100 microns. The positioning system scans the probe and charts position with measured electrochemical parameters, creating a data map of local current.
-
product
Probe Cards
Vertical Probe Card. (Mobile D-RAM, L.D.I Flip Chip 60um Pitch,. System LSI, Soc Devices). Cantilever Probe Card. Low Leakage Probe Card.
-
product
Near Field Micro Probe ICR HV H Field
The measurement coil is located vertically in the probe head. The near field probes are run with a positioning system (Langer Scanner).
-
product
VX4 System
PrecisionWoRx
The PrecisionWoRx VX4 System gives test facilities and probe card manufacturers the ability to confidently test tighter pitches and smaller probe tips. The system can be easily configured to specific requirements for a variety of probe card technologies. For processes using cards with very small probe tips, the system’s high-resolution optics deliver a detailed field-of-view for high accuracy and repeatability.
-
product
Near Field Micro Probes ICR HH H Field
The measuring coil is horizontally located in the probe head. The near field micro probes are operated with a positioning system (Langer Scanner).
-
product
Remote Test Unit (RTU) Expert
RTU Series
VeEX’s Remote Test Units (RTU) are self-contained, scalable test and monitoring probes for communications networks. When used as part of the VeSion cloud-based monitoring system, these rackmount probes are optimized to work with a centralized server system. In addition, the probes can be operated in standalone mode via web browser.
-
product
Fully Manual Systems
SPS-1000, SPS-2000, and SPS-2200
The SPS-1000, SPS-2000, and SPS-2200 systems are MicroXact’s premier manual probe stations designed to be flexible and easy to use. The high level of performance and affordability of these manual probe systems put them in a class of their own.
-
product
Electromagnetic Immunity Scanner
SmartScan BASIC
The BASIC is manually operated system for performing susceptibility scanning at the system level with minimal data storage capability. This system includes:1. Up to 8kV (optional. 4kV base) pulse generator for ESD susceptibility testing- Camera and camera shutter to take DUT picture and failing spots- Control computer2. Up to 8kV Probe Sets:- 1mm Hx/y Field Probe- 5mm Hx/y Field Probe- D=8mm Hz Field Probe- D=8mm Ez Field Probe- Contact API for custom design probes3. Manual input of testing location and failing condition over the DUT to be included in final report.
-
product
EZL Viscosity Mounting System
Sample handling and probe mounting may often be the deciding factors in a successful viscosity measuring system. The EZL Viscosity Mounting System provides an excellent mounting platform for in-line viscosity measurement with the Dynatrol® DV Viscosity Probes.
-
product
Oscilloscope Probes
Teledyne LeCroy has a wide variety of world class probes and amplifiers to complement its product line. From the ZS high impedance active probes to the WaveLink differential probing system which offers bandwidths up to 25 GHz, Teledyne LeCroy probes and probe accessories provide optimum mechanical connections for signal measurement.
-
product
Probe Card Analyzers
PB1500
The PB1500 is a low cost probe card analyzer system. It has the capability to perform all the tests done on the larger PB3600/6500 probe card analyzers, but at a lower cost for low pincount cards. A maximum of 1,280 channels may be configured in the PB1500 MUX system. The Precision Measurement Unit (PMU) has the same accuracy, repeatability and range as the larger analyzers. The repair process consists of selecting a failing probe, which moves it under the binocular microscope and positions a crosshair over the correct position for that probe.
-
product
NeoScan
NeoScan® is a unique electric field measurement system with unprecedented innovative features. NeoScan systems utilize EMAG’s patented, electro-optic (EO) field probe technology. Unlike conventional near-field scanning systems that require metallic pickup radiators or sensors, NeoScan probes are made of absolutely metal-free parts.
-
product
Temperature Calibration
In our temperature lab we have the capability calibrate a wide range of temperature products such as catering food probes from deli to restaurant, industrial systems for manufacturing and quality checks using thermocouples surface probes or insertion probes we also calibrate IR (Infrared) thermometers.
-
product
Active RF Probe 3 GHz - 0.2 pF - 1:10
RFP 3
The Active RF Probe provides a very low capacitive load of the system to be measured.
-
product
IPTV Monitoring and Test Solutions
Net-x TVMS
The NET-xTVMS is a system of specialized computer probes networked to the enterprise server and clients. The probes, strategically located at the hub sites next to edge routers and edge QAMs, continuously monitor IPTV QoS with MPEG-TS transport metrics of SPTS and MPTS multicast streams as well as DVB-C MPTS streams. The NET-xTVMS is scalable from 1 to 1000 probes. Several types of probes are available to suit many different monitoring applications. Metrics are collected at the probes and alarms are sent to the server once they exceed predefined thresholds. A system wide alarm matrix, alarm logs and periodic metrics for each location can then be viewed via Internet on client computers.
-
product
Fault Injection and White-Box Testing
VectorCAST/Probe
VectorCAST/Probe is integrated with the full family of VectorCAST tools allowing probes to be inserted during Unit, Integration, or System Testing. The probe insertions are controlled by the same technology that controls our code coverage instrumentation, which ensures that the probes function correctly regardless of the compiler, target processor, or run-time environment.
-
product
AFM & SPM Probes
Nanonics offers a wide variety of custom-made probes for Nanonics MultiView systems to meet all your imaging, writing, manipulation, and characterization needs. See below for different categories of probes we offer.
-
product
Ultra-High Vacuum
KP Technology offer a range of Kelvin Probes that work under ultra-high vacuum conditions, choose from single-point or scanning probes to add to your existing vacuum chamber, customize the UHV corner cube or consider the newest addition to the range, the Ф4 ultra-high vacuum scanning Kelvin Probe system.
-
product
contact/non-contact portable 3D measurement system
ScanArm
The FARO ScanArm combines all of the advantages of the FaroArm with a hand held laser scanner and is the perfect contact/non-contact measurement system. Unlike other scanning systems, the ScanArm’s hard probe and the Laser Line Probe can digitize interchangeably without having to remove either component. Users can accurately measure prismatic features with the hard probe, then laser scan sections requiring larger volumes of data — all in one simple tool.
-
product
Flying Prober Test System
QTOUCH1404C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
product
Linear Polarization Resistance Probes
Linear polarization resistance (rosion probes are commonly used in the water treating industry and other environments where instantaneous, on-line corrosion rate readings are required. Linear polarization probes are ideally suited to monitor fluctuations that may occur within a system; for example, these probes can be used to monitor corrosion inhibitor effects on a regular basis.
-
product
Pilot Control Software Suite
The SemiProbe PILOT Control Software Suite semiautomatic and fully automatic probe systems employs the SemiProbe patented Adaptive Architecture. Software modules can be added to the base system as needed. PILOT Control Software consists of a Microsoft Windows-based user interface built on the SemiServer application for communicating to and from the probe system. Individual customer applications can be integrated with PILOT Control Software for a customized system to meet individual needs.
