Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
LXI WTB Probe, Thru connect, DC coupled
60-981-001
The 60-981 LXI Wired Trigger Probe provides a simple method of monitoring the LXI Wired Trigger Bus activity. It provides a through line active probe that can be used to non-intrusively monitor the waveforms of the M-LVDS drivers on all 8 channels. Each channel has two single ended outputs from the differential pair that can be subtracted by an oscilloscope to display each driver output and the differential signal.
-
-
product
Probes
RTD
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
product
Probes
Type K
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
product
Probes
Pro-Series®
Pro-Series High Temp Cooking Probe 6" Long probe with a right angle bend for easy pulling from meats or turkeys. Cable withstands 700°F to better withstand broiling and grilling temperatures. Probe tip and sensor read temperatures to 572°F for deep-frying. Good general-purpose probe, the length reaches the center of large roasts and turkeys.
-
product
Probes
SHOCONA Probes are designed for non-vibrating, contact mode applications and are compatible with most commercially available SPMs/AFMs. These probes are nanofabricated using highly doped single crystal silicon with unparalleled reproducibility, robustness and sharpness for consistent high resolution imaging capabilities. This is a box of 10 probes.
-
product
Probes
2800 Series
Many sensor heads, or probes, are available for use with our 4800 series and 8800 series capacitive position sensor. The resolution of our capacitive position sensors is determined by a combination of the active sensing area of the probe, the measurement range, and the measurement bandwidth of the electronics unit (demodulator). Please refer to the Model 4810 data sheet for complete details on probe selection, including mechanical dimensions of our standard probes.
-
product
Probes
Metrix* proximity probes are interchangeable with Bently Nevada** Series 3300, 7200, and 3000. All probes incorporate the latest technology and include agency approvals.
-
-
product
Probe
Net-EXP
The NET-EXP Probe is an expandable probe that can be purchased with an initial amount of bandwidth of as little as 0.5 Gbps and expanded up to 5 Gbps by merely additional software license.
-
product
Probes
D-COAX offers four analytical probe models: HyPac model for package characterization, and two models, Omni and OmniJet, for board level characterization, and DP1.4mm diffenrential, single-ended probe.
-
product
Probes
Sper Scientific portfolio of probes provides the right solution for your testing needs, backed by years of product innovation and technical support. All of our probes are designed to meet the accuracy, ease of use, durability and flexibility for your water quality testing needs.
-
product
Probes
Hygro-i Series
The Tramex Hygro-i ® relative humidity probe is the most advanced, resilient and reusable RH probe on the market today. Used in conjuntion with Tramex CMEX II and MRH III moisture meters, the Hygro-i ® relative humidity probes allow the user to perform in situ and hood type RH testing to comply with ASTM F2170 and British Standards BS 8201, 8203, 5325 for the Flooring Industry, and is ideal for use by Flood & Water Damage Restoration and Indoor Air Quality professionals.
-
product
Probes
Fujian Lilliput Optoelectronics Technology Co., Ltd.
We are one of the leading and professional probes manufacturers and suppliers in China. Thanks to our highly qualified experts and advanced technology, we are also one of the world's leading brands. Welcome to buy the quality, cheap and durable probes in stock from us. Check the quotation with us now.
-
product
Probes
70 Series
American Probe & Technologies, Inc.
The series is for all probes that are non-standard in shank diameter (other than 10 or 20 mil).
-
product
Probes
72 Series
American Probe & Technologies, Inc.
20 mil (0.020") shank sizesAvailable in straight and bent shapes to fit most industry standard analytical probe holders
-
product
Probes
Prepare the IM6/Zennium for special fields of application like high impedances, low impedances, very low capacitance or boost the compliance voltage.
-
product
Probes
71 Series
American Probe & Technologies, Inc.
10 mil (0.010") shank sizesAvailable in straight and bent shapes
-
product
Probes
measures relative pressure range from -1 to 60 bar and -14 to 870 psi and comes with wireless connection low energy.
-
-
product
Probes
Replacement or Additional 9V 230V/110V Power Supply. Requires a standard IEEE mains interface cable
-
product
Probe Positioners (Probe Manipulators)
PacketMicro offers a broad ranges of probe positioners to allow designers to guide standard oscilloscope/TDR/RF/microwave probes onto the small geometries of fine-pitch interconnects, SMD packages, MCMs, hybrids and ICs.
-
product
ProBus Probe Adapter for TekProbe-BNC Probes
TPA10
- Allows TekProbe interface level II probes to work with any ProBus-equipped Teledyne LeCroy oscilloscope- Automatic probe detection- Provides all necessary power and offset control to the attached probe- Supports probes up to 4 GHz- Easy firmware updates- Wide variety of probes supported including: Preamplifiers, Current Probes, Single-Ended Active Probes and Differential Active Probes
-
product
RF Coaxial Probes & Probe Positioner
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
product
Single Probe Scanning Probe Microscope
MultiView 2000
an advanced single probe scanning probe microscope enabling a variety of modes of AFM/SPM/NSOM imaging. Nanonics has designed The MultiView 2000TM for excellence in scanning probe microscopy while allowing for near-field and far-field optical NSOM/Raman/TERS imaging without perturbation. The Multiview 2000TM is the only commercially available instrument that offers both tip and sample scanning. This versatility is important for different operation modes where the user can now choose whether the sample or tip is static. The Multiview 2000TM further offers the most stable feedback mechanism available in the form of normal force feedback with tuning fork actuation.
-
product
Thermocouple Probes
Type T
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
product
Test Probes
Safety right angle insulated alligator test probe, safety right angle insulated alligator test probe with insulated jaws, test probe, minitest probe, micro test probe.
-
product
Accessibility Probe
Shenzhen Chuangxin Instruments Co., Ltd.
Temperature test probe surface temperature probe
-
product
Probe Systems
These flexible probe stations are designed for the ever-changing test configurations required in a engineering lab. Combined with durable probes or your own high-speed probes, PacketMicro probe stations are the most cost-effective probing solutions in the industry.
-
product
Mini Probes
TST3PK
Mini Probe: Easy to use plug-in style current testers, simple way to verify current flow in a socket.- Complete Kit – TST3PK- USB PROBE – TSTUSB- ACC PROBE – TST12V- VAC PROBE – TST110V
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
