Showing results: 451 - 465 of 2825 items found.
-
SimpleSleuth -
SimpleSoft Inc.
SimpleSoft's SNMP Vulnerability Probes enable administrators and manufacturers to quickly and easily test enterprise SNMP v1, v2c and v3 implementations for vulnerability to denial-of-service (DoS) attacks.
-
AP472S1 -
Delta OHM S.r.L.
Vane probe with K type thermocouple ∅ 100 mm to measure air speed in the range 0.6…25 m/s and air temperature in the range –25°C … +80°C.
-
LP471UVBC -
Delta OHM S.r.L.
LP471UVBC is a radiometric probe for measuring irradiance (W/m²) in the 210…355 nm spectral range with peak at 265 nm. It is equipped with a connector with SICRAM module and a 2 m cable
-
MBP850 -
Silicon Control Inc.
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
FLP850 -
Silicon Control Inc.
The PCIE850 provides a complete test and debug solution for PCI Express Bus. Interposers and probes connect to the PCIE850 providing access to PCI Card, AMX, XMC and VPX systems.
-
EverBeing Int'l Corp
Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.Everbeing offers GGB’s high impedance active probe for failure analysis of your devices. The high impedance with low capacitive design allows measurements of internal nodes without loading the device. For more information, please visit http://www.ggb.com.
-
DF-600 -
Link Instruments
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
SONOSCAN I -
SONOTEC GmbH
The SONOSCAN immersion transducers for Non-destructive Testing (NDT) are mainly used to test metals and plastics for the smallest material defects. For example, binding defects, welding defects or cracks and pores in metal parts can be detected. The powerful, robust ultrasonic probes can be connected to all common ultrasonic testing devices. Due to variable designs and sizes, the immersion probes guarantee optimal use. In addition to ultrasonic standard pobes, we also offer customized transducers according to your individual specifications.
-
STAr Technologies, Inc.
STAr's functional test cantilever probe cards represent the finest technology on the market for wafer-sort, built-in self-tests (BIST), known good die (KGD), burn-in, image sensor etc.
-
Tektronix, Inc.
Optimized for power integrity measurements, these probes combine low noise contribution, DC offset up to 60 V, high bandwidth, low loading, and a wide range of connectivity alternatives.
-
Delcom Instruments Inc.
Rolling 2 or 4 point probe. Roller width and diameter, as well as ring number, spacing, and elevation, are specified by customer. Monitor and record remotely with included Ethernet and PC-based software.
-
T0211-4 -
COMET SYSTEM, s.r.o.
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
T0211 -
COMET SYSTEM, s.r.o.
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
T0211-2 -
COMET SYSTEM, s.r.o.
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Omega Engineering, Inc
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.