Showing results: 1141 - 1155 of 2825 items found.
-
LF1 set -
Langer EMV-Technik GmbH
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
N2142A -
Keysight Technologies
The Keysight N2142A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 75 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
N2140A -
Keysight Technologies
The Keysight N2140A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 200 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
Huntron
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design. Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
-
SONOSCAN Q -
SONOTEC GmbH
In addition to angle beam probes according to european standards (EN), we offer probes with quick-change wedges for ultrasonic weld seam inspection as well as various wedges for the american market. Quick-change probes are used wherever access to the inspection object is difficult to reach with the larger AWS transducers. The relatively small, round elements also offer better defect resolution.
-
MFA 01 set -
Langer EMV-Technik GmbH
The micro probes are used to measure magnetic fields and they have a high resolution. They measure magnetic fields up to 6 GHz, e.g. at signal conductors (150µm), SMD components (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the Bias tee BT 706. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee BT 706 to a spectrum analyzer or an oscilloscope. Langer EMV-Technik GmbH includes correction lines in the delivery. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
MFA 02 set -
Langer EMV-Technik GmbH
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
PPE6KV-A -
Teledyne LeCroy
High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.
-
-
PK-HVA-01 -
Teledyne LeCroy
Replacement Alligator Clips for High Voltage Differential Probe
-
PK-HVA-03 -
Teledyne LeCroy
Replacement Hook Clips for High Voltage Differential Probe
-
PK-HVA-02 -
Teledyne LeCroy
Replacement Pincer Clips for High Voltage Differential Probe
-
PK-HVA-05 -
Teledyne LeCroy
Replacement Spade Terminals for High Voltage Differential Probe
-
72-190 -
Tenma
A compact and lightweight probe for the analysis and troubleshooting of logic circuits. The probe will recognise high, intermediate and low level pulses in DTL, TTL, HTL and CMOS logic circuits. Works as a pulse detector, pulse stretcher and a pulse memory.
-
Extech 881616 -
Extech Instruments Corporation
The Extech 881616 is a Type-K magnetic grill temperature probe. For use with any meter that has a Type-K connector. This grill temperature probe features a temperature range from -40°C to 200°C (-40°F to 392°F).