Showing results: 856 - 870 of 1688 items found.
-
95EA -
ShinewayTech
OFS-95EA optical fiber fusion splicer is designed with high-speed image processing technology and special precision-positioning technology. It will automatically finish the whole fiber fusion process in 9 seconds by fast mode, and splice loss is lower than 0.02dB for single mode fiber. 3.5-inch LCD, dual CMOS monitors, X and Y axis separately display or simultaneously display, thus different fusion stages can be showed clearly. It is compatible with ITU-T SM/MM/DS/NZDS/ED fiber, and is equipped with 4-in-1 holders and SOC adapter.
-
McLAREN Applied Technologies
The unit can acquire data from on-board interfaces at rates of up to 10 kilosamples per second, and from remote units via communications links. A high-performance on-board PowerPC microprocessor offering over 1000MIPS processing power hosts customer applications for real-time data analysis. Application code may be autocoded using our Graphical Development Environment (GDE) from Matlab/Simulink control modules. Data is logged to 2GB of on-board Flash memory and downloaded for analysis via a Gigabit Ethernet network connection.
-
FlashLink BLE -
DeltaTRAK
Monitor temperature and locationTracks route and conditions inside vehicles during deliveryTracks conditions in storage, processing and packing facilitiesView data on mobile device up to ~100 feet / 30 meters awayNo need to open doors and locate logger for downloadingWirelessly transmits data to smart devices with appCustomize settings: ID/name, logging interval, high/low alarm limitsEmail PDF and CSV reports from mobile device and web appData stored in a cloud-based applicationAnalyze information from any web enabled device to make cold chain management decisions
-
R400a -
Lectrosonics, Inc.
The R400a is a high performance, triple-conversion, frequency synthesized, UHF receiver fully compatible with all Lectrosonics 400 series transmitters, and a number of analog models. The proprietary audio processing includes a DSP (digital signal processor) for very low distortion and a superior signal to noise ratio. The DSP eliminates a compandor and its artifacts to provide exceptional audio quality when operating in its native hybrid mode. Special DSP algorithms also provide compatibility modes for use with Lectrosonics 100 and 200 Series analog transmitters.
-
Curtiss-Wright Defense Solutions
Curtiss-Wright addresses the demands for increased data and signal processing performance, along with flexible interfaces for handling sensor I/O, through our full line of FPGA processor cards. Our rugged FPGA cards supporting Xilinx FPGA devices are designed to perform reliably in the harshest military environments. Available in 3U, 6U and XMC form factors, they offer flexible interfaces for handling sensor I/O and support the long lifecycle of defense and aerospace programs by offering backward pin compatibility to enable easier migration from generation to generation.
-
MW180 -
Milwaukee Instruments
The Milwaukee MW180 5-in-1 MAX pH/ORP/EC/TDS/NaCl/Temp. Logging Bench Meter has won fans around the world with its reliable, fast and simple operation as well as its tough, sleek design and small benchtop footprint. It is accurate to ± 1% of reading for EC/TDS/NaCl and up to +/-0.002 pH, with automatic or manual temperature compensation and a built in dedicated GLP key. Ideal for use by education, horticulture, labs, food processing, water treatment and many other applications with challenging pH/ORP/EC/TDS/NaCl/Temp. measurement needs.
-
MW151 -
Milwaukee Instruments
The Milwaukee MW151 MAX 3-in-1 pH/OPR/Temp. Logging Portable Bench Meter has won fans around the world with its reliable, fast and simple operation as well as its tough, sleek design with a small lab footprint. The MW151 MAX is accurate to ± 0.002 pH with automatic or manual temperature compensation with a built in dedicated GLP key. Ideal for use by brewers, wine makers, growers, labs, food processing, water treatment and many other applications with challenging pH measurement needs.
-
Multichannel Strain Gauge Meter -
ZETLAB Company
The Software Multichannel strain gauge meter is used for performing all types of strain gauge measurements using strain gauge sensors (for instance, force and torque sensors, bridge and semi-bridge circuits based on resistive strain sensors), strain measurement data acquisition modules ZET 017-T and digital strain gauge sensors of ZETSENSOR series. The program enables simultaneous processing of up to 128 measuring channels using strain gauge station and up to 500 measuring channels in the case if digital sensors are used.
-
Finna Sensors
OMNIR is the future of near infrared moisture sensing technology. Coming from OMNI, meaning “all” and NIR, meaning “near infrared,” Finna Sensors has created an intelligent all-sensing solution that exceeds expectations. It not only delivers accurate data instantaneously and non-destructively, it also monitors its own health to perform its best during your crucial processing moments. By selectively harnessing light, to ensure increased uptime and greater profitability for your operation, the future of your manufacturing operation starts now.
-
PCI595 -
Vadatech Inc
The PCI595 is based on the Xilinx XCVU440 Virtex UltraScale FPGA, which provides 2,880 DSP slices, 88.6 Mb RAM and 5,541,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to one DDR4, 64-bit wide, with 8 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
RFM700-M -
Xylem Analytics UK ltd.
RFM700-M series refractometers are robust, low cost, fully automatic instruments that are ideally suited to the food, sugar and beverage industries but can now be used in many other non food applications where use of temperature control is not required. RFM700-M Series refractometers are robust, low cost, fully automatic instruments that are ideally suited to the food, sugar and beverage industries but can also be used in many other non-food applications where temperature control is not required, for example measuring sugar (Brix) concentrations in the food processing industry.
-
iNSTiTUT DE RECHERCHE ET COORDiNATiON ACOUSTiQUE/MUSiQUE
The analysis of sounds includes methods enabling the permanent extraction or automatic structuring of diverse sorts of information given off by the signal, such as the fundamental frequency or the spectral evolution determining the pitch and timbre of a perceived sound. Information outside what is strictly musical is also taken into consideration, notably concerning industrial acoustics, sound design and multimedia as well as the automatic indexing of recorded sounds. The methods used are based on signal processing, statistical analysis, information theory, machine learning and recognition techniques, but also on knowledge of auditory perception.
-
Hoka Electronic B.V.
CODE300-32 Standard is a software solution to demodulate, decode and analyze digital signals transmitted via radio. Our software don't requires special hrdware part for processing the signal. The audio signal can come from traditional receivers and handled with a common soud card already included on all PC and Notebook, SDR receivers, signal recorded and stored in a standard audio file, it is also possible to use audio signals from the LAN, signals in I/Q format, and digital audio signals from virtual soundcard.
-
Fortress Technology Inc.
Stealth Vent Tube metal detectors are custom manufactured to integrate into any bottling application. The Stealth detects Vent Tube nozzles and metal contaminants in filled plastic or glass bottles of up to 3 liters/6.5 pints capacity. The Stealth uses digital signal processing technology and has high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
Model 7811 -
Pentek, Inc.
Model 7811 is a member of the Cobalt® family of high performance XMC modules based on the Xilinx Virtex-6 FPGA. A multichannel, gigabit serial interface, it is idealfor interfacing to Serial FPDP data converter boards or as a chassis-to-chassis data link. The 7811 is fully compatible with the VITA 17.1 Serial FPDP specification. Its built-in data transfer features make it a complete turnkey solution. For users who require application-specific functions, the 7811 serves as a flexible platform for developing and deploying custom FPGA processing IP.
