Showing results: 346 - 360 of 683 items found.
-
48Pro2 -
Dataman, Inc
The Dataman 48Pro2 is a super fast PC based universal 48-pin programmer with ISP capabilities and USB 2.0 / parallel connectivity • Up to 75% faster programming of high-capacity memory devices • Over 105,000 devices supported with new devices added monthly • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Full ISP capabilities including JTAG compatibility • Hi-speed USB 2.0 connectivity • Easy to use software compatible with the latest operating systems including Windows 10 • Multiprogramming support allows one PC to control up to four units programming independently or as a gang programmer • Comprehensive 3 years parts and labor warranty
-
ISequenceSpec -
Agnisys, Inc.
The complexity of modern SoC has raised the requirement for HW/SW co-simulation to catch the bugs from the early design stage. There is lack of common set of sequences which can be shared across the teams. ISepenceSpec helps design teams to generate the unified test and programming sequences in UVM and Firmware from the specification. ISequenceSpec uses the register information from importing the standard formats like IP-XACT, SystemRDL, XML. User can define the test sequences in a simple editor, and then generate the unified test sequences from verification to validation.
-
MRC ltd.
Constantly calculates and adjusts the Voltage and Current limit points according to availablemaximum power (160W)At maximum current (10A), voltage is limited to 16V;at maximum voltage (42V), current is limited to 3.8ADual action rotary encoder control with push knob for fine and coarse tuning Remote control for Programming, Output Voltage/Current, and ON/OFF using supplied software, driver,and USBStore 20 presets with up to 999 cycles each on a PCvia USB and supplied SoftwareOutput Voltage: 0 to 42VOutput Current: 0 to 10ABasic Accuracy: (0.2%+5 counts)
-
MeasureReady™ 155 -
Lake Shore Cryotronics, Inc.
The MeasureReady™ 155 Precision I/V source combines premium performance with unprecedented simplicity for materials scientists and engineers requiring a precise source of current and voltage. Low RMS noise: from 200 nV (10 mV)/7 pA (1 µA). Bipolar, 4-quadrant power source. DC and AC modes supported up to 100 kHz*. Full scale ranges from 10 mV to 100 V (1 μA to 100 mA). 0.001% programming resolution (from 100 nV/10 pA.
-
Ahloborn
A wide range of probes, sensors and signals is available for ALMEMO® data loggers and measuring instruments, which are connected via intelligent connectors with integrated data carrier. For common measuring tasks the connectors are configured at the factory and the measuring device automatically recognizes the connected sensor. All sensors can be calibrated, scaled and provided with a unique designation via the intelligent connectors. The programming always remains with the corresponding sensor, so that it can be connected to any input on the measuring instrument. Inaccuracies of a sensor can be corrected in the connector, thus turning simple sensors into precise transducers.
-
2100 -
The Eastern Specialty Company
The TESCO Desktop Meter Station is an extremely versatile piece of testing equipment. It can be used as a programming station, a single meter evaluation station, or a test bed for checking meter features and anomalies. The newly designed Meter Station not only has the ability to simply warm-up meters, but also has optional features such as an external load (1PH) or an internal phantom load (0.5A), an optional disconnect operation (1000VA XFMR), a load receptacle, or a tilt chassis. For easy operation, all options are conveniently mounted on the front panel.
-
NI
The Multifunction I/O Device features I/O with varying channels, sample rates, output rates, and other features to meet many common measurement requirements. You can use the device for industry applications such as laboratory automation, research, and design verification. The included DAQExpress companion software provides basic measurement and analysis, while the included NI-DAQmx driver provides the ability to create customized automated measurement and control applications. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
NI
The C Series Temperature Input Module features up to 16 channels of temperature input from either thermocouples or RTDS. This module can include anti-aliasing filters, open-thermocouple detection, and cold-junction compensation. Additionally, the module also feature isolation for safety, noise immunity, and high common-mode voltage range.The C Series Temperature Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
TPA 300 -
Bosch Diagnostics
The Bosch TPA 300 is a comprehensive TPMS tool designed for sensor programming, activation and ECU reset. The full-color, intuitive interface guides the user when replacing and servicing TPMS sensors. When paired with a compatible Bosch diagnostic scan tool, like ADS 325 or 625, users can reset the ECU in less than two minutes. The TPA 300 supports all known OE and aftermarket programmable sensors for all light vehicles. Frequent updates allow new features, vehicles and sensor coverage to be added regularly.
-
53210A -
Keysight Technologies
Single-channel, RF frequency counter One 350 MHz input channel, plus optional second channel (6 GHz or 15 GHz)10 digits/second resolution Built-in math analysis and color, graphical display (trend and histogram)LXI-C/LAN, USB, GPIB Optional: Lithium Ion Battery BenchVue software enabled: Do more with your PC and instrument together, no programming required. Easily control your counters, quickly build automated tests and log data for faster analysis and save precious time.
-
NI
The C Series Voltage and Current Input Module features up to 16 input channels with built-in noise rejection. You can use this module to combine the two most common inputs to reduce the overall number of modules you need in your measurement system.The C Series Voltage and Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Chroma ATE Inc.
Adjustable criteria for different process application or modelFlexible algorithms programming editor for mono-crystalline and multi-crystalline silicon solar cellsMultiple interface to communicate with manufacturing equipment or information systemVarious defects inspection capability from multilayer LED lighting designFlexible design that can be easily integrated to your in-line printing system and sorting system
-
U9401B -
Keysight Technologies
The Keysight Medalist i1000D is now even better. Improving from its previous state of an analog-only ICT, the new digital release of the system now features per pin programmable digital cards and a whole new set of intuitive software graphical user interfaces (GUIs) that makes programming and development effortless.
-
848Pro2 -
Dataman, Inc
The Dataman 848Pro2 is a super fast stand-alone gang programmer with eight independent 48-pin ZIF sockets, ISP capabilities and internal control PC driven by Windows Embedded 8.1 Industry Pro • Stand-alone operation with touch screen control • Internal control PC driven by Windows Embedded 8.1 Industry Pro • Up to 75% faster programming of high-capacity memory devices • Over 105,000 devices supported with new devices added monthly • Independent modules supporting concurrent programming • Intelligent pin drivers operate down to 1.8V so you'll be ready to program the full range of advanced low-voltage devices • Full ISP capabilities including JTAG compatibility • Comprehensive 3 years parts and labor warranty • Free life-time software updates
-
TestBuilder -
elowerk Testsystems
elowerk TestBuilder is the operating software for elowerk test systems. TestBuilder is based on the Microsoft .Net Framework and runs on Windows Vista and Windows XP. Test programs can be created by CAD data import. The comfortable graphical user interface allows a straightforward editing of test programs. Customized applications can be programmed using a programming interface.
