Showing results: 826 - 840 of 1106 items found.
-
779989-01 -
NI
32-Channel, 50 MHz, 200 MB/s PXI Digital I/O Module—The PXIe‑6537 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
780695-01 -
NI
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
NI
Multifunction Reconfigurable I/O Devices feature a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop (HIL) testing, custom protocol communication, sensor simulation, and high-speed control.
-
779988-01 -
NI
32-Channel, 25 MHz, 100 MB/s PXI Digital I/O Module—The PXIe‑6536 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
NI
The PXI Serial Interface Module offers a number of options for connecting to serial hardware. You can choose from common serial protocols, such as RS232, RS422, and RS485. The PXI Serial Interface Module also offers various isolation, hyperthreading, and multiprocessor compatibility options as well as 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
CPCI-7500 -
TEAM SOLUTIONS, INC.
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
CM8 -
North Atlantic Industries
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
USHIO DEUTSCHLAND GmbH
USHIO developed a UV meter series to measure intensities of UV radiation. As an add-on, the temperature is also registered. You can decide between the high-end UV meter UIT-250, and UIT-201. The former has a wider measurement range, allows the measurement of energy doses and has the capability to transfer the data via a serial communication protocol to a PC. Various sensors are available. The most popular sensors have center wavelengths at 254 nm, 365 nm or 410 nm.
-
Sy629PCIe-BPTE -
Sycos AES
The Sy629PCIe-BPTE card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory. In particular, this product can emulate up to 120 terminals transmitting on an ARINC-629 data bus whilst correctly maintaining the approved Basic Protocol. This product also offers enhanced facilities to enable a user to insert transmission errors onto the bus and detect and report errors in received messages.
-
OP-SB5GL -
LINEEYE Co., Ltd.
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
OBB2 -
Astronics Corporation
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
CRY2100 Series -
CRYSOUND
CRY2100 series noise sensor has tiny structure and is equipped with precision measurement microphone which guarantees a good temperature and humidity characteristics. Noise sensor which integrates with signal conditioning circuit and DSP chip can provide dynamic range up to 110dB, and measure the ambient noises as low as 25 dBA. Noise sensor also has an RS-485 bus interface which can support Modbus RTU protocol, and a 4-20mA analog signal output port.
-
Scientech Technologies Pvt. Ltd.
Variety of Instruments are being used in education, industry and research in the field of analog, digital, instrumentation, control system, biomedical and RF domain, requirement of these instruments varies and depends on their application areas.Some application like electronic, electrical, automation, etc. require standard waveforms, arbitrary waveforms, variable digital pattern and protocol generation. Analog signal combination and multiple digital signals are also required for some applications like power electronics, embedded, DSP and VLSI.
-
780 Series -
Teledyne LeCroy quantumdata
The Teledyne LeCroy 780 series handheld test instruments for HDMI® are battery powered (except 780C, 780D and 780E), portable video and audio generators and HDMI analyzers that enable you to conduct quick, on-site verification testing and troubleshooting of your HDMI system and analog video displays. The 780 series instruments are equipped with both a reference source and a reference sink interface allowing you to test audio, video and protocols of any type of digital video device: sources, repeaters and sinks.
-
OP-SB85L -
LINEEYE Co., Ltd.
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
