Filter Results By:

Products

Applications

Manufacturers

Protocol

A standard way of controlling hardware and/or software that enables connection, communication and data transfer.

See Also: NTCIP, Communication Protocol


Showing results: 841 - 855 of 1114 items found.

  • Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O

    CM8 - North Atlantic Industries

    The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).

  • 4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V

    CPCI-7500 - TEAM SOLUTIONS, INC.

    *This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS

  • UV Meters

    USHIO DEUTSCHLAND GmbH

    USHIO developed a UV meter series to measure intensities of UV radiation. As an add-on, the temperature is also registered. You can decide between the high-end UV meter UIT-250, and UIT-201. The former has a wider measurement range, allows the measurement of energy doses and has the capability to transfer the data via a serial communication protocol to a PC. Various sensors are available. The most popular sensors have center wavelengths at 254 nm, 365 nm or 410 nm.

  • PCIe Multi-Terminal Emulator

    Sy629PCIe-BPTE - Sycos AES

    The Sy629PCIe-BPTE card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory. In particular, this product can emulate up to 120 terminals transmitting on an ARINC-629 data bus whilst correctly maintaining the approved Basic Protocol. This product also offers enhanced facilities to enable a user to insert transmission errors onto the bus and detect and report errors in received messages.

  • TTL/I2C/SPI* Expansion Kit

    OP-SB5GL - LINEEYE Co., Ltd.

    OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.

  • Databus-to-Network Interfaces

    OBB2 - Astronics Corporation

    The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.

  • Noise Sensor

    CRY2100 Series - CRYSOUND

    CRY2100 series noise sensor has tiny structure and is equipped with precision measurement microphone which guarantees a good temperature and humidity characteristics. Noise sensor which integrates with signal conditioning circuit and DSP chip can provide dynamic range up to 110dB, and measure the ambient noises as low as 25 dBA. Noise sensor also has an RS-485 bus interface which can support Modbus RTU protocol, and a 4-20mA analog signal output port.

  • Scientech Multi Instruments

    Scientech Technologies Pvt. Ltd.

    Variety of Instruments are being used in education, industry and research in the field of analog, digital, instrumentation, control system, biomedical and RF domain, requirement of these instruments varies and depends on their application areas.Some application like electronic, electrical, automation, etc. require standard waveforms, arbitrary waveforms, variable digital pattern and protocol generation. Analog signal combination and multiple digital signals are also required for some applications like power electronics, embedded, DSP and VLSI.

  • PXI Digital Reconfigurable I/O Module

    NI

    PXI Digital Reconfigurable I/O Modules feature a user-programmable FPGA for onboard processing and flexible I/O operation. You can completely control the synchronization and timing of all signals and operations along with custom onboard decision making. The PXI Digital Reconfigurable I/O Module is suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom communications protocols, bit error rate testing, and other applications requiring precise timing and control.

  • Handheld Test Instruments for HDMI

    780 Series - Teledyne LeCroy quantumdata

    The Teledyne LeCroy 780 series handheld test instruments for HDMI® are battery powered (except 780C, 780D and 780E), portable video and audio generators and HDMI analyzers that enable you to conduct quick, on-site verification testing and troubleshooting of your HDMI system and analog video displays. The 780 series instruments are equipped with both a reference source and a reference sink interface allowing you to test audio, video and protocols of any type of digital video device: sources, repeaters and sinks.

  • TTL/I2C/SPI Expansion Kit

    OP-SB85L - LINEEYE Co., Ltd.

    OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.

  • 50/100G PAM4 Pin Photodiodes

    Macom Technology Solutions Holdings Inc.

    MACOM offers high sensitivity PIN photodiodes with industry leading performance at speeds of 56Gbd / 100G. Proprietary designs enable operation using PAM4 modulation protocols in 50 /100G applications. The high responsivity designs have high reliability and are suitable for use in both tele-communications and datacenter networks. The high bandwidth PIN photodetectors are available in a back illuminated design (highest performance), a front illuminated design (more cost effective) and in both singlet and array form factors

  • Digital I / O modules

    Acery Technologies

    The 34950A module has 64-bit bi-directional lines and can be configured with 8 8-bit digital I / O channels with handshaking capability. Each 8-bit channel has programmable polarity and a threshold of up to 5V. The memory can be used to generate or capture digital patterns up to 10 MHz. It provides seven configurable handshaking protocols for a wide range of applications. In addition, two counter / totalizer channels can be used to compute events, frequency, period, duty cycle, accumulation, and pulse width.

  • Mobilize

    Protec Instrument Corp

    A complete wireless solution that connects your Pronk test equipment to your smart device!* Take complete control of your Pronk products — Safe-T Sim® Mobilize Electrical Safety Analyzer,  Mobilize SC-5 SimCube® NIBP Simulator, Mobilize OX-2 OxSim Flex® SpO2 Simulator, and Mobilize FlowTrax® IV Pump Analyzer — to set up your own test protocols or run your CMMS procedures right from your Apple iOS device.

  • Detective Logic Analyzer

    LPDDR5 - FuturePlus Systems

    Provides logic analyzer like deep transaction Listing and Waveform captureCan store up to 512M of captured States at up to 6400+ MT/sContinuous, real time analysis, not post-processing2D (voltage & time) Eye Detector guarantees valid data acquisition on each signalExtensive Triggering and Storage Qualification allows precise insightIndustry Leading Protocol Violation Detector provides hundreds of simultaneous, real time tests to JEDEC specifications, NOT post processing. No other tool can provide this!Mode Register Listing provided

Get Help