-
product
Single Channel Peak Power Meter
8501A
The Spanawave/Giga-tronics 8501A Single Channel Peak Power Meter combine CW power measurement with the ability to make precise peak power measurements at any point on a pulsed waveform. This dual, built-in capability lets you make CW measurements and analyze pulsed waveforms with a single instrument.
-
product
RF Signal Source
DSG800A
The DSG800A delivers outstanding performance in the same class of economical RF signal sources with full frequency and power scanning capabilities, as well as AM/FM/ØM analog modulation, powerful pulse modulation and newly added IQ modulation. Compared to similar products, the DSG800A has the smallest footprint, light weight and superior portability, making it an excellent choice for educational laboratories, industrial production lines, development and research applications.
-
product
Precision Source / Measure Unit, 1-Channel, 10 FA Resolution, 210 V, 3 A DC / 10.5 A Pulse
B2911B
The Keysight B2911B precision source / measure unit (SMU) is a 1-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current. It easily measures current versus voltage (I/V) with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
product
PED Systems
Pulsed Electron Deposition
Is a process in which a pulsed (80-100 ns) high power electron beam (~1000 A, 15 kV) penetrates approximately 1 μm into the target resulting in a rapid evaporation of target material. The non-equilibrium heating of the target facilitates stoichiometric ablation of the target material. Under optimum conditions, the target stoichiometry is preserved in the deposited films. All solid state materials – metals, semiconductors and insulators, including those transparent to laser wavelengths in PLD – can be deposited as thin films with PED. By combining PLD and PED, the range of complex materials that can be prepared as thin films can be greatly enhanced.
-
product
DC Pulse Current Capacitor
Both series can be customized as Low Voltage High Capacitance High Current Capacitors.We can customize Snubber Capacitor as Box type and support other parameters.For 250Vac~900Vac / 400Vdc~1,350Vdc and with higher Current requirement, please refer to our AC/DC Power Capacitors.Different applications can have very different capacitor electrical and mechanical profile requirements.Please feel free to send your application details for a suggestion and quotation.
-
product
SFG Spectrometer
Ideal laser spectroscopy tool for in-situ investigation of surfaces and interfaces. SFG spectrometer operates from 4300 to 625 cm-1 and provides < 6 cm-1 spectral resolution. The heart of the system is a picosecond Nd:YAG laser generating 25 ps pulses that pump an OPG/DFG delivering from 260 to 20 µJ per pulse across the IR range
-
product
Pulse Evaluation Systems
*Intuitive, user-friendly handling*Integrated wide-range power supply*Easily programmable output functions*Devices for monitoring standstill, speed, direction, slip, and frequency*Switching relays and transistor outputs, scalable analog output
-
product
Pulse Concentrator
1) Total counter indexes of 12 pulse inputs with tariff and unit information, date and time information and alarm states can be displayed on the 2x12 characters LCD screen automatically with intervals of 5 seconds or manually by pressing up and down buttons,2) Enabling the backlight for 20 seconds by pressing any button to provide easy reading on the screen,3) Data communication with a PC via RS-485 output,4) Storing the contents of each pulse input with tariff information in 1-60 minutes intervals on the 2 MB permanent memory of the device with date and timeinformation,5) Preventing changes to settings by unauthorized users by defining a 4-digit user password.
-
product
Fixed Mount Strobes
Our fixed mount stroboscopes are designed for installation in applications requiring continuous stroboscopic visual inspection. The MVS is available with xenon or LED light output with adjustable pulse width and focal distance for optimized target illumination. Connect your existing trigger signal or the optional Frequency Controller with LCD. Connect multiple units together in parallel for applications with wide illumination area requirements. Use the optional Audio Interface Box and microphone to create stunning audio driven visual effects.
-
product
Mini OTDR Fiber Optic Reflectometer with VFL OPM Laser Source
MT-1300 Plus
Guangzhou Wanglu Communications Co., Ltd.
- Display: 3.5 inch color TFT-LCD screen- Handheld design, light weight and easy operation- Single mode: 1310/1550 nm- Dynamic range: 24 / 22dB (can test about 60 km)- Automatic measurement mode: 1310/1550 nm dual wavelength can be tested simultaneously- Applicable fiber: SM- <8m extra-short event dead zone- Wavelength: 1550nm- Up to 24dB High Dynamic Range- Distance Range: 4,8,16,32,64,128,256km- Pulse width: 3ns-10us- RJ45 cable TDR test & cable sequence test- Optical power meter, Visual fault locator, Laser source- Event Map, can display the length of the link, the type of event point and the position of break point.- USB interfaces, supporting USB stick and printer and direct cable download to PC via ActiveSync- LED light- Built-in friendly-environment lith ium battery with high capacity for over 12 hours of operating life
-
product
Laser Diode Driver
LDD100
Artifex Engineering GmbH & Co. KG
The LDD100 employs a digitally programmable analogue end stage for flexible and accurate current control. Currents of up to 600A with pulse durations of 50ns to 3s are generated with rise and fall times of 70ns (F-version) or 600ns (XL-version) – essentially without overshoot. Due to the flexibility in setup and control, the LDD100 is practical for many laboratory applications. For automated measurements, the unit may be directly controlled via the USB interface. Alternatively, all parameters may be input via the graphical software or via the integrated keypad and OLED display.
-
product
Test System
4003 TLP+™
The Model 4002 TLP+™ test system was the first turn-key commercial TLP developed for the ESD industry and has remained the leader in the ESD square pulse testing field since this method was first introduced in 1989. This tester is the ultimate design and analysis tool for ESD protection circuits. It provides Pulse Curve Traces of circuit characteristics which simulate ESD tests. This allows you to see into a chip’s operation taking out the guesswork which speeds your design and minimizes lost time.
-
product
Ring-Loop TWTs
Communications & Power Industries
Small and lightweight products for pulsed radar and most advanced designs for commercial, electronic warfare and radar systems, the unique ring-loop slow-wave structure used in these CPI BMD traveling wave tubes provides high gain at kilowatt peak RF power levels without oscillation and achieve greater than 30% efficiency.
-
product
Demonstration Board
SAMPULSE20x2
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
product
Chronometrer
CHA20
This digital chronometer enables the user to measure the time between two pulses generated either by a dry contact, a TTL input or an AC or DC voltage.
-
product
Transient Immunity Tester
KES7700
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAEJ1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
-
product
Charged Plate Monitor
Model 280A
Simco-Ion’s Model 280A incorporates enhanced circuitry that enables it to more accurately measure the performance of high frequency AC ionizers, as well as pulsed DC ionizers and steady-state DC ionizers. The Model 280A can be used as a portable CPM and is capable for of up to 6 hours of operation on the internal battery before recharge.
-
product
Intelligent Detection Units
Measurement of the ambient dose rate equivalent of continuous and average dose rate of pulsed X-ray and gamma radiation in an extremely wide range in harsh operating conditions.
-
product
PXIe-6614, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module
782353-01
PXIe, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module—The PXIe‑6614 is a high-precision counter/timer module that performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS‑compatible digital I/O. The PXIe‑6614 offers industrially rugged features for a wide array of applications such as automotive/aerospace, industrial/motion control, and manufacturing test. Measurements are highly accurate and precise over longer periods of time because of the oven‑controlled crystal oscillator (OCXO) in the module.
-
product
Microwave Comb Generator
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
product
Cluster Series Systems
The quadrupole analyser is a precision assembled triple mass filter with unique, independently driven RF only secondary filter stages preceding and following the primary mass filter. A UHV low profile electron impact ioniser with twin oxide coated iridium filaments and a pulse ion counting single channel electron multiplier detector are included as standard. A Faraday detector option extends the dynamic range to 5 x 1010.
-
product
Signal Conditioners & Interface
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
product
POWER PROBE 4 MASTER KIT
PPKIT04
*Combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit testing capabilities*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)*Tests fuel injectors, module drivers (transistors) and works as a circuit detector with the PPECT3000
-
product
COMPUTERIZED LCRTZ TEST SYSTEM (Automatic Transformer Test System)
CVCT-S20
Ideal for fast and fool proof testing of COILS AND SMALL TRANSFORMERS like SMPS transformers, Telecom transformers (HYBRID, POT CORE, RM-CORE), Pulse transformers etc. The systems scans at one stroke, all the windings of a transformer and tests as per definition of test procedure. The test procedure can be pre-programmed and stored under User friendly menu driven software . Any semi-skilled and unskilled person can be engaged for actual testing purpose. Can Select test frequency, pin number, parameters, test conditions, limits for each test. Test any pin to any other pin any defined parameter.Test Parameters :-> Inductance-> Capacitance-> AC Resistance, -> DC Resistance, -> Impedance, -> Leakage Inductance,-> Transformation Ratio & Winding PolaritySPECIFICATIONS :Measurement Frequencies : 50 Hz, 100 Hz, 500 Hz, 800 Hz; 1 KHz, 2 KHz, 5 KHz, 10 KHz. Measurement Voltage: 0.1 V – 1.0 V RMS adjustable under program control.
-
product
Pulsed Power
Alpha-Omega Power Technologies, LLC.
Alpha-Omega Power Technologies (AOPT) specializes in high voltage pulsed power design and manufacturing. AOPT has industrial proven design ranging in power from a few hundred watts up to 50 kilowatts. We can design and build a complete turn-key system to meet your requirements. Please Contact Us to discuss your requirements.
-
product
AXIe High-Speed Digitizer/DAQ, 10-bit, 10 GS/s, DC to 2.5 GHz BW
M9710A
Based on the AXIe standard, the M9710A is a unique 10-bit high-speed digitizer, capturing signals from DC up to 2.5 GHz at 5 GS/s. It provides excellent measurement accuracy and high dynamic range across four phase-coherent channels within a single card. Optimized response allows few hundred picoseconds pulse analysis. Moreover, an interleaving option allows acquisition at 10 GS/s on two combined channels, keeping excellent measurement fidelity.
-
product
Standard Digitizer
725S Family
The 725S family is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window). The wide range of DPP algorithms supported by the 725S make it a “must-have” for any type of nuclear physics application.
-
product
Standard CW Amplifiers
The BT-AlphaA-CW series is a range of classAB RF power amplifiers covering the 10kHz to1MHz frequency range. Rugged, solid-state design - high reliability. Extremely high phase and amplitude stability. High linearity. In-Built Protection. Very fast blanking. Capable of pulsed operation. Competitively priced. Suitable for CW radar, communications, HF/VHF jamming, particle accelerator applications/plasma systems, plasma, RF heating and other scientific applications.
-
product
USB Power Sensor - 100 MHz to 8 GHz, Average, Peak (Pulse)
GT-8551B
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
product
Synchronous Generator
ZET 7190
The Synchronous generator ZET 7190 is intended for generating sine, pulse, saw-shaped signals. It has 2 synchronous channels and can be used individually, or as a part of control and automation systems.
