Showing results: 2176 - 2190 of 3194 items found.
-
BAT-200 -
Neulog
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
ERAVANT
A Scalar Network Analyzer is a type of RF network analyzer that is used to measure only the amplitude properties of a DUT (Device Under Test). Unlike a Vector network Analyzer, it does not measure both amplitude and phase of the DUT.
-
IQgig-IF -
LitePoint Corporation
When used in conjunction with IQgig-RF, it supports over-the-air (OTA) testing of WiGig RF modules and end-products. The IQgig family products provide total test solution for R&D characterization and high volume manufacturing.
-
BroadWave Technologies, Inc.
BroadWave designs and manufactures Coaxial Adapters and other coaxial RF components that are ideally suited for test, verification and system integration. Our products offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
Teledyne Defense Electronics
Teledyne Advanced Electronic Solutions integrates CCAs and other sub-assemblies, cables and fabricated parts into system modules shipped directly to customers for integration into their products.- Box Build: custom built to order system solutions- High complexity box assemblies and subsystems- High frequency RF box assemblies and subsystems- Full functional RF testing up to 26 GHz (K band)- Multi-level systems integration – build and test modules and CCAs and integrate into higher level assemblies- Custom cell design for customer subsystems- Special bonding processes including thermal management and vibration- Robust torque and FOD control programs- System level testing including functional, vibration and thermal- Complex harness fabrication and integration- Fiber-Optic and RF waveguide integration and testing- Large system capacity in excess of 200 lbs.- Configure to order – Integrate different options, firmware, configurations, etc across a single order as required
-
CCI
A form of intermodulation distortion that occurs in components normally thought of as linear, such as cables, connectors and antennas. However, when subject to the high RF powers found in cellular systems, these devices can generate intermodulation signals at –80 dBm or higher.
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Freese Enterprises Inc.
Freese Enterprises (FEI) has vast experience, in many industries, in the custom design and construction of physical test fixtures to consistently test a feature or operation of a device or piece of software. FEI can develop test solutions for modules or fully assembled products such as key fobs, RF filters, and cell phones - from complex integrated circuits and custom electronics to automotive components and RF communication devices. In general, the advantages of FEI test fixtures include the separation of the test initialization and destruction from the testing, reusing a known state for more than one test, and assumption by the testing framework that the fixture set-up works.
-
LXinstruments GmbH
The in-vehicle test set was developed to successively measure several active RF amplifiers installed in the vehicle as well as different antenna structures. It offers the possibility to connect 12 DUTs. The DUTs can be connected to an external spectrum analyser via a 1 to 12 RF multiplexer. Each DUT can be individually switched and supplied with an adjustable voltage via a bias-tee integrated in the system. The individual bias voltages and currents are recorded by the IVTS and can be called up on an interactive control panel or via Ethernet and SCPI commands. The complete system can be powered by rechargeable battery and can be operated either via Ethernet, fibre optics or WLAN.
-
Smiths Interconnect
Smiths Interconnect offers Wafer Level Chip Scale Package (WLCSP) Probe Heads utilizing spring probe technology which provide high parallelism in test, superior signal integrity and high speed / RF testing capability.
-
Teledyne Lincoln Microwave
Teledyne Lincoln Microwave design and manufacture RF amplifiers utilising the latest semiconductor technology. Our portfolio includes low noise amplifiers (LNA’s), power amplifiers and pre-amplifiers. These can incorporate linearization, filtering, phase and amplitude control functionality.
-
60-721A-004 -
Pickering Interfaces Ltd.
The 60-721A High Performance Video MUX is designed for the switching of RF signals in 75 Ohm systems at frequencies up to 1GHz. It is ideal for 75 Ohm monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment.
-
Analog Systems
CATV Power Supply Super Model are designed to give full current with built in power inserter and short circuit protection. They can provide Power Pass voltage (current) through RF cables to drive amplifiers and Nodes in CATV networks.
-
60-721A-006 -
Pickering Interfaces Ltd.
The 60-721A High Performance Video MUX is designed for the switching of RF signals in 75 Ohm systems at frequencies up to 1GHz. It is ideal for 75 Ohm monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment.
-
60-721A-005 -
Pickering Interfaces Ltd.
The 60-721A High Performance Video MUX is designed for the switching of RF signals in 75 Ohm systems at frequencies up to 1GHz. It is ideal for 75 Ohm monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment.