Filter Results By:
Products
Applications
Manufacturers
-
product
RF Filters
Raymond RF offers a complete line of RF filters ranging from 0.4A to 600A in both stand-alone and cabinet-mounted configurations for our QuietBoxes and Anechoic Chambers. Both styles of filters can be supplied with NPT pipe nipples and flange nuts for mounting directly on a QuietBox or Anechoic Chamber. Alternately, both styles of filters can be remotely mounted with shielded conduit running between the clean end of the filter and the QuietBox or Anechoic Chamber.
-
product
RF PHY Tester
TLF3000
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
product
RF Shield Box
CMW-Z10
The R&S®CMW-Z10 has excellent shielding effectiveness and superior coupling characteristics.The shield box can be used for frequencies up to 6 GHz.The antenna structure is optimized to enable excellent radio connections between the DUT and tester.The highly broadband spiral antenna allows a wide variety of applications.These outstanding features combined with modular options make the RF shield box indispensable for any radiocommunications tester.
-
product
RF Signal Testers
RF Signal Generators, Record & Playback Systems, Players, Productivity Tools and More
-
product
Radio Communication Tester
CMP180
The R&S®CMP180 radio communication tester is a future-proof, non-signaling testing solution for wireless devices in research and development, validation and production. Together with advanced frequency, bandwidth and RF capabilities, it enables testing of new wireless technologies such as Wi-Fi 6E, Wi-Fi 7, 5G NR FR1 and many more. Additionally, the doubled number of analyzers (2xVSA), generators (2xVSG) and RF ports (2x8) enable simultaneous measurements of technologies and devices in a VSA/VSG single-box tester.
-
product
2 X91 to 4) 50 Ohm 2.5Ghz RF Multiplexer
YAVHF3X450
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced!
-
product
Custom Radio Direction Finding Products
This assembly contains three sets of antennas, three RF summers, an antenna switch, a GPS and (optionally) a flux gate compass. The pod mounts to the roof with nylon straps, although it is recommended that it be bolted down for more permanent applications. Although this antenna is not stocked, we can provide them on relatively short notice. No minimums apply.
-
product
Fixed Site Radio Direction Finders
Our VHF/UHF/THF direction finders typically are installed in permanent or semi-permanent locations where the antenna has a relatively clear view of the surrounding area and RF obstructions and reflectors are minimal. Three stackable antennas mounted on top of a mast, tower, or building cover 115 – 1000 MHz. in three frequency bands. It can be remotely operated via an Ethernet or radio-modem connection. Networked with other fixed site or mobile direction finders and utilizing our TargetTrack software facilitates geolocation of the targeted RF emitter.
-
product
Scalable Microwave Subsystems with Open-Architecture Ethernet/LXI Platform
EX7000 Series
The EX7000 family is the industry’s first series of scalable microwave subsystems built on an open-architecture Ethernet/LXI platform. This innovative family of products simplifies the development of custom RF Interface Units (RFIU) requirements with its common hardware platform and software communications interface, while maintaining the look and feel of a standard COTS product.
-
product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
product
2x (1 to 8) +1X (2 to 1) 50 Ohm 2.5GHz RF Multiplexer Terminated
YAV92501
2x (1×8) Mux + 1×2 + 2x Pass trough 30Vac/dc, 10W Max Max current 500mA Control port CAN o Ethernet (con Ethernet to CAN Gateway) Dissipative
-
product
4x (1 to 4) +1x (4 to 1) 50Ohm 2.5 GHz RF Multiplexer with Self Test Relays
YAVAL022
5x (1×4) Mux + 2x Pass trough Selftest function 30Vac/dc, 10W Max Max current 500mA Reflexive
-
product
PXIe Down Converter: 4 Channels, 2-16 GHz RF, 0.01-2.4 GHz IF
M5201A
Single-slot PXIe low-IF downconverter module with a 2 to 16 GHz RF input frequency range and 0.01 to 2.4 GHz IF range
-
product
PXIe RF AWG: 4 Channels, DC-16 GHz, 2 GHz IBW
M5300A
The M5300A is a two-slot PXIe module with four high-speed AWG outputs, clock input and output, and eight triggers. It provides high-performance with easy-to-use programming libraries, real-time sequencing technology, and FPGA programming.
-
product
RF Switches
The Ideal Switch has proven to be an ideal replacement for large high-power RF electromechanical relays, as well as RF/microwave solid-state switches, where linearity and insertion loss are critical parameters.
-
product
2 x(1 to 4) 50 Ohm 2,5GHz RF Multiplexer with CAN
YAVHF3X4C50
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
product
2 x(1 to 4) 75 Ohm 2,5GHz RF Multiplexer with CAN
YAVHF3X4C
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
product
2 x(1 to 4) 75 Ohm 2,5GHz RF Multiplexer
YAVHF3X4
Fixture friendly. Use this product inside a Faraday chamber, and benefit from the fact that wiring in-out the chamber is drastically reduced! This module features three multiplexers in cascade configuration, for frequencies up to 2,5GHz. In/out is through SMB connectors, selectable for 75 and 50 Ohm. There’s direct control of the relays (24Vdc) or integrating CAN bus interface.
-
product
RF Sensor for Spectrum Monitoring
N6841A
Reduce operating costs with affordable spectrum monitoring and TDOA geolocation measurementsDeploy fully capable RF monitoring stations faster with simple hardware and measurement-specific software24/7 real-time remote spectrum monitoring with Signal Surveyor 4D softwareCapture intermittent signals with spectrum analysis softwareFaster search and signal isolation with broad attenuation and wide dynamic rangeLocate narrow or wideband signals with geolocation software
-
product
RF Products
Ducommun is a leading global supplier of RF Products for Commercial Aerospace, Military & Space markets. We partner with top-tier OEMs and primes because of our unique, comprehensive understanding of electro-mechanical and RF principles. Whether you need a standard, off-the-shelf or in-stock coaxial switch, or a highly customized millimeter wave product, Ducommun offers a range of products and solutions to meet your program and design requirements.
-
-
product
Phase Noise Measurement Solutions
Keysight offers dedicated phase noise measurement solutions to simplify your measurements and maximize your efficiency. Building on 30 years of low phase noise and RF design and measurement experience, our innovative solutions are designed to provide the most accurate phase noise data possible, and are economically tailored to fit your specific performance and application needs - now and well into the future.
-
product
Isolator
A 2-port device that transmits microwave or radio frequency power in one direction only while blocking the signal in the opposite direction.
-
-
product
Attenuator & Signal Calibrator (30MHz Receiver)
VM-7
The TEGAM Model VM-7 is a 30MHz receiver that performs precise measurement of RF power ratios over a wide dynamic range. It offers averaging, high resolution, and offset features to improve measurements and speed accessible through front panel keystrokes, or remotely through a GPIB controller.
-
product
Low Cost RF Power Sensor Calibrator (100 kHz to 18 GHz)
1827
Calibrates 100 kHz to 18 GHz RF power sensors in 30 minutes or less; two Switchable RF inputs; Thermistor RF Power Standard is internally temperature controlled; Type IV Bridge Circuitry; DC Power Levels can be measured to within 0.003%.
-
product
Low Cost RF Power Sensor Calibrator (10 MHz to 18 GHz)
1825
Calibrates 10 MHz to 18 GHz RF power sensors in 30 minutes or less; Thermistor RF Power Standard is internally temperature controlled; Type IV Bridge Circuitry; DC Power Levels can be measured to within ±0.003%.
-
product
RF Thermistor Power Meter
1830A
Thermistor based RF power sensors are universally recognized as the most accurate means to measure and transfer RF power. Compatible with thermistor power sensors from: Agilent (HP), TEGAM, Weinschel, Hughes, General Microwave, Millitech. Supports 100 and 200 thermistors. Integrates bridge balancer and power meter into one package. Four digit calibration factor resolution. Full remote programmability. Heater control for ovenized sensors. LXI Compliant.
-
product
LitePoint RF Test System
J750
The option of adding LitePoint instrumentation to the J750 system delivers a cost-effective, complete production test solution covering global wireless connectivity standards.
-
product
EMC/EMI
Electromagnetic Compatibility (EMC) or Electromagnetic Interference (EMI) testing deals with your products’ Radio Frequency (RF) emissions and immunity to RF. EMC testing ensures that your product will operate as intended in the intended environment and it won’t interfere with other products used in its same electromagnetic environment.
