Showing results: 526 - 540 of 845 items found.
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
7Layers, Inc.
SAR measurements, ie the measurement of the specific absorption rate, checks the amount of radiated high-frequency energy that a human body z. B. is exposed while using a mobile phone, laptop, data card. SAR measurements enable an assessment of the relative safety of radio devices with low power (low-power transmitters), which are used in close proximity to the human body.
-
Pasternack Enterprises, Inc.
RF solid state power amplifier (SSPA) PE15A4006 from Pasternack is part of the largest selection of in-stock radio frequency microwave and millimeter wave amplifiers available for same-day shipment. This Pasternack solid state RF power amplifier is a medium power amp design constructed in a connectorized package. Our SSPA is designed with SMA connectors and rated at 1 Watt.
-
Copper Mountain Technologies
Vector network analyzers are a valuable tool for radio technicians. VNAs allow you to tune frequency dependent components including transmitters, combiners and isolators, circulators, duplexers and filters. With a VNA you can measure and adjust S11 parameters, measure return loss, or analyze and fix response issues. CMT offers compact VNAs ideal for benchtop and field use.
-
MLT1600 -
W2BI Inc.
The MLT1600 addresses the testing challenges of IoT products across multiple cellular radio technologies – such as GSM, WCDMA and LTE – with a 70-MHz to 6-GHz frequency range. With its portable design and small footprint, the MLT1600 leverages W2BI’s existing cloud-based test management platform to acquire on-demand test cases and publish test results as required across all test parameters.
-
PMT-330 -
Sensortech Systems, Inc.
The Process Sensors Portable Moisture Tester (PMT-330) puts the capabilities of an on-line moisture analysis and control system into the palm of your hand, allowing operators to spot-check moisture content of boards, wood, plastic, and paper products quickly and easily. It features radio frequency dielectric (RF) measurement technology that penetrates the surface of products and instantly displays accurate moisture data.
-
QDUC -
Analog Devices Inc.
Analog Devices digital up/downconverters serve as the frequency translator and digital filter between data converters and DSP blocks. These innovative products enable highly programmable and configurable receive and transmit signal chains, allowing multichannel, multicarrier radio platforms in 3G wireless base stations. They also meet the digital data conversion requirements for many other communications applications.
-
DFA300 -
Doble Engineering
Use the Doble DFA300 to identify and locate insulation defects.This surveying tool combines radio frequency interference (RFI) and acoustic emission (AE).The The DFA300 partial discharge detector can locate partial discharge (PD) in a few seconds. Designed for surveying live, high voltage apparatus, its versatility makes it the perfect, multi-purpose tool for condition-based maintenance programs.
-
Pasternack Enterprises, Inc.
RF limiting amplifier PE15A6002 is rated at -40 dBm minimum power input and 10 maximum power input. Our limiting radio frequency amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial limiting amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
GL Communications Inc.
Wireless networks can impair voice, video, and data quality by various means including poor mobile phone quality, voice compression and decompression algorithms, video compression and decompression algorithms, delay, loss or gain in speech levels, noise, acoustic and landline echo, and other distortions. GL provides a compact and portable solution for Wireless Devices, and Mobile Radio testing.
-
Model 8266 -
Pentek, Inc.
The SPARK® Model 8266 is a fully-integrated PC development system for Pentek Cobalt®, Onyx®, Flexor®, and Jade™ PCI Express (PCIe) software radio, data acquisition, and I/O boards. It was created to save engineers and system integrators the time and expense associated with building and testing a development system that ensures optimum performance of Pentek boards.
-
60-760-005 -
Pickering Interfaces Ltd.
The 60-760-005 is a single 24x8 High Frequency Matrix Module suitable for switching frequencies up to 50MHz. It has an impedance of 50Ω and uses BNC signal connectors. It is also available in a smaller enclosure with SMB Connectors. It is designed to provide simple and scalable switching for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
EMC Instruments Corporation
Anechoic chamber, radio isolation room construction, removal, maintenance and repair. System Integration of complete Test System. Development team has the expertise and technical experience and provide a customized service demand, the project includes a full range of EMI / EMS / RF test equipment with neighboring sell and repair reference signal source Noise Generators Signal Generators
-
LKZ-1000 -
Sonel S.A.
*Passive or active modes of tracing.*Detection of underground live wires.*Detection of underground wires with no voltage (radio mode).*Detection of underground wires with no voltage using a transmitter (galvanised, inductive or clamp-based connection).*Tracing metallic or non-conductive pipes using an additional probe.*Tracing non-conductive pipelines using a “floating” probe.*Tracing a determined cable.*Determining the depth of a cable.
-
FB7-NX -
National RF, Inc
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
