Filter Results By:

Products

Applications

Manufacturers

Showing results: 766 - 780 of 1185 items found.

  • Voltage Absence Tester

    C.A 762 - Chauvin Arnoux Metrix

    The CA 762 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.

  • 4 Serial Communication Channels, Programmable RS-232/422/485, Non-Isolated

    SC6 - North Atlantic Industries

    Serial Communication Module SC6 provides up to 4 high-speed, programmable RS-232/422/485, individually non-isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel non-isolated returns are available as part of the channel user interface signal set (for SE or SYS-GND reference).

  • 4 Serial Communication Channels, Programmable RS-232/422/485, Isolated

    SC5 - North Atlantic Industries

    Serial Communication Module SC5 provides up to 4 high-speed, programmable RS-232/422/485, individually isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel isolated returns are available as part of the channel user interface signal set (for SE or ISO-GND reference).

  • Electrical Tester

    C.A 742 - Chauvin Arnoux Metrix

    The C.A 742 Voltage Absence Tester is an essential tool for any electrician to check that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 3 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in certain countries, there are 2 references, with or without IP2X accessories.

  • Comb Generator, 10 MHz To 110 GHz

    U9391M - Keysight Technologies

    U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.

  • FPGA Mezzanine Card

    FMC160 - Abaco Systems Inc

    The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.7Gsps (2.85Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. It is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1).

  • DC - 400 MHz PC-Based Timer Interval Analyzer

    Guide Technology, Inc.

    GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.

  • Dytronic Primary Transfer Ultra Stable Standard

    RD-22 Ultra - Radian Research, Inc.

    The RD-22 Dytronic Primary Transfer Ultra Stable Standard represents the state-of-the-art technology in a commercially available AC transfer reference. The Ultra Stable RD-22 is a variant of the RD-22 Primary Transfer Standard that has been optimized for 120/240 V @ 5A operation to provide optimum stability. In a stable test environment, repeatability for a 10-second test of ±0.6 µWh/VAh is attained at 120 V and 240 V at 5A inputs with a 95% confidence interval. A typical experimental 2 repeatability of less than ±0.25 µWh/VAh is achieved. In a stable test environment, a reproducibility of ±2 µWh/VAh over a five-day interval is attained at 120 V and 240 V at 5A inputs with 95% confidence interval.

  • PCI Express Receiver Board

    AD12-2000-IRIGB - Ultraview Corporation

    The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.

  • Rack-Mounted Timing Systems

    CommSync II Family - FEI-Zyfer Inc.

    The CommSync II family of modular systems provide GPS time and frequency outputs to meet your synchronization requirements. All systems include support for multiple input and output modules including 1PPS, IRIG, HAVE QUICK, PTTI, IEEE-1588 PTPv2, low phase noise 1, 5, and 10 MHz sine wave as well as custom outputs.These systems are available with military SAASM MPE-S GB-GRAM, SAASM Force 22E MRU or civilian C/A GPS receivers. Rubidium or OCXO oscillators provide for excellent holdover performance in the event of failure of the reference inputs. In addition, they may be configured as Distribution Time and Frequency (DTF) systems that are synchronized by an external reference. Dual Redundant systems (CommSync II & CommSync II-D) may be configured with two GPS Time & Frequency (GTF) modules and two power supply modules (AC and/or DC power) for redundancy with uninterrupted automatic switchover.

  • Multi-Scanners

    AMETEK Sensors, Test & Calibration

    We offer a signal multi-scanner which provides a time-saving, automatic solution to calibrate multiple temperature or pressure sensors simultaneously. The scanner may be combined with our dry-block or liquid calibrators, DTI reference thermometers, pressure calibrators, and ASC multifunction process calibrators. Use any place where temperature and/or pressure measurement is critical and there is a need to create traceable documents for sensor calibration.

  • 1500V Multifunction I-V Curve Tracer

    SOLAR I-Ve - HT Italia Srl

    SOLAR I-Ve allows both testing a single-phase (three-phase with optional MPP300) photovoltaic system and verifying I-V curve. Thanks to remote unit SOLAR02, it is possible to test the system complying with the requirement of simultaneity as provided for by the reference standard. SOLAR02 is a datalogger which, synchronized with SOLAR I-Ve, acquires the data relevant to irradiation and temperature while tests carried out by SOLAR I-Ve are carried out.

  • OPTICAL PHASE NOISE TEST AND MEASUREMENT SYSTEM

    OEwaves, Inc

    OEwaves’ HI-Q® Optical Test Measurement System utilizes a homodyne methodology for automated measurement capable of testing ultra-low phase noise laser sources. The user friendly test system is capable of rapidly measuring laser phase noise and estimating its FWHM linewidth down to < 3 Hz without complex setup or reference lasers normally required to make such a narrow linewidth measurement.

  • Programmable S/R Standard & Simulator

    5300 - North Atlantic Industries

    NAI’s 5300 Synchro/Resolver Standard & Simulator is a laboratory-grade, programmable instrument. This model can be used as a true Synchro/Resolver standard for calibrating and testing Automatic Test Equipment (ATE) for Calibration/Metrology Labs, and for Engineering Design and Production Test environments. It can also be used to measure Angle Position Indicators (API) and Synchro-to-Digital converters for static or dynamic characteristics. This model also may use an external reference waveform.

  • Precision Resistor Network

    Analog Devices Inc.

    Analog Devices provides a portfolio of quad resistor networks with excellent matching specifications over the entire temperature range. All of our resistors can be accessed and biased independently, making them a convenient and versatile choice for any application that can benefit from matched resistors. Our resistor networks provide the precise ratiometric stability required in highly accurate difference amplifiers, voltage references, and bridge circuits.

Get Help