Showing results: 196 - 210 of 4029 items found.
-
50-115A-022 -
Pickering Interfaces Ltd.
This is the 25xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
50-115A-121 -
Pickering Interfaces Ltd.
This is the 64xSPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
50-110A-121 -
Pickering Interfaces Ltd.
This is the 64xSPDT version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
50-115A-122 -
Pickering Interfaces Ltd.
This is the 50xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
50-115A-021 -
Pickering Interfaces Ltd.
This is the 32xSPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
50-110A-021 -
Pickering Interfaces Ltd.
This is the 32xSPDT version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
CXM/3x1 to CXM/12x1 -
Cytec Corp.
CXM/3x1 to 12x1-NO-SMA Microwave Relays are Normally Open (NO) in the OFF state. Only one port can be on at a time. Larger configurations can be built by connecting the common port of multiple relays to another relay in series.
-
60660 -
Lisle Corp.
Jumpers have tabs for clamping and flat pads to place test leads on. No need to pierce wires or connect multiple jumper wires. Also Includes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter. Jumper wire may be used between common and open to close the relay circuit for testing and has a test port to easily check voltage. Also provides access for a clamp-on amp meter. Relay Puller Pliers easily remove electrical relays without damage to the relay or electrical box.
-
DP-VXI-4503 -
Data Patterns Pvt. Ltd.
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
GDJB-II -
HV Hipot Electric Co.,Ltd.
GDJB-II type Single phase relay protection tester is the updated calibration device for relay testing. It shows clear data, operation is easy.
-
PW466i -
Ponovo Power Co., Ltd.
PW466i (6×20A, 6×150V) 6-phase relay tester is a powerful secondary injection protective relay testing kit with 6-currents and 6-voltages sources.
-
K3163i -
KINGSINE Electric Automation Co., Ltd.
◆ Digital signal complying IEC61850-9-1 / IEC61850-9-2 protocols.◆ Synchronize with GPS,IRIG-B.◆ Suitable testing for all kinds of electromagnetic relays,microcomputer relays.
-
GDJB-PC -
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1.GDJB-PC Universal Secondary Injection Relay Test Set is applied to test the relay unit in relay protection system. 2.At the same time GDJB-PC Universal Secondary Injection Relay Test Set could be considered as a universal three phase AC/DC voltage source or current source. 3.It can work alone or connected to computer, inside the relay controller there are new speed digital signal mini PC and real DAC (Digital-to-Analog Converter) template with new high fidelity and high power, the machine has large panel screen and rotating mouse. It is small in volume, high precision.
-
V210 -
Highland Technology, Inc.
The V210 is a single-wide, 6U VME module that includes 64 SPDT relays and drivers. User-settable DIP switches set the A16/A24 VME address mode, VME address, and select whether the relays are statically operated or operate in latching mode, where relay states are sustained when VME crate power is off.
-
56810 -
Lisle Corp.
Set includes four jumpers to fit the most popular size relays on domestic and import vehicles. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using green four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on. Set comes in blow-molded case for storage.