Filter Results By:
Products
Applications
Manufacturers
Remote Terminal Unit
Collects data from data acquisition (DAQ) devices and transmits the information to the main test system via a network.
- Pickering Interfaces Inc.
product
PXI Single Bus 74-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-301
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
Remote Terminal Units
ComTroll
ComTroll is a modular system with different building-blocks allowing the utilities to tailor-make a system to meet their own requirements for each monitored and controlled location.
-
product
RTU (Remote Terminal Unit)
R2+ RTU
*The R2+ Remote Terminal Unit (RTU) is a distributed architecture and large I / O capacity designed to meet the various demands of current Power SCADA / EMS applications.
-
product
Intelligent Remote Terminal Unit
The ADAM-3600 is a new series of ADAM models which leverage IoT technology for RTU applications. They not only have high environmental adaptability, to work in, far and wide remote locations, but also has a new form factor that is ideal for installation in remote terminal units.
-
product
Remote Terminal Unit (RTU) Replacement
Schweitzer Engineering Laboratories, Inc.
Compared with typical RTUs, SEL automation controllers provide improved reliability, extended I/O contacts, and advanced automation and control for remote substations and field applications.
-
product
Gateways & Remote Terminal Units (RTUs)
Linux-based Gateways and RTUs offer edge communication for remote maintenance, acquiring data and trasmitting to higher-level management systems.
-
product
2x 3U OpenVPX MOSA Remote Interface Unit
SIU32-RIUVARM-01
SIU32-RIUVARM-01 is a Modular Open Systems Approach (MOSA) Remote Interface Unit (RIU) to manage, monitor and control connected I/O, communications, measurement and simulation interfaces through Ethernet commands from a main mission processors. Extremely low power with 2 x 10/100/1000Base-T Ethernet.
-
product
4x 3U OpenVPX MOSA Remote Interface Unit
SIU34-RIUVARM-01
SIU34-RIUVARM-01 is a Modular Open Systems Approach (MOSA) Remote Interface Unit (RUI) to manage, monitor and control connected I/O, communications, measurement and simulation interfaces through Ethernet commands from a main mission processors. Extremely low power with 2 x 10/100/1000Base-T Ethernet.
-
product
PCI-8361, PCI Host, 100 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
781394-01
The PCI‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8361 card provides a PCI link over a copper cable to the PXI‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PXIe-8383MC , x8 PCI Express 2.0, PXI MultiComputing Remote Control Module
782971-01
The PXIe‑8383mc is an adapter module that allows two or more intelligent systems to exchange data via PCI Express. Because of the excellent data transfer characteristics of PCI Express, the PXIe‑8383mc enables PXI systems to transfer data at multi-gigabytes per second of practical data throughput with only a few microseconds of latency.
-
product
PCIe-8361 , x1 Gen1 PCI Express Host, 208 MB/s, 1-Port, Copper Cable MXI-Express Device for PXI Remote Control
779504-01
The PCIe‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI Express slot. The PCIe‑8361 remote controller provides a x1 PCI Express link over a copper cable to the PXIe‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PXIe-8301, Thunderbolt™ 3 PXI Remote Control Module
785679-01
Thunderbolt™ 3 PXI Remote Control Module—The PXIe-8301 enables laptop control of a PXI Express chassis over a Thunderbolt™ 3 connection. Using a Gen 3 x4 PCI Express link, the PXIe-8301 allows up to 2.3 GB/s of sustained data throughput between the chassis and laptop over a Thunderbolt 3 USB Type-C cable. An additional Thunderbolt 3 port allows for connecting additional Thunderbolt or USB-C devices. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
PCIe-8362, x1 Gen1 PCI Express Host, 208 MB/s, 2-Port, Copper Cable MXI-Express Device for PXI Remote Control
779502-01
x1 Gen1 PCI Express Host, 208 MB/s, 2-Port, Copper Cable MXI-Express Device for PXI Remote Control - The PCIe‑8362 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI Express slot. The PCIe‑8362 remote controller provides a x1 PCI Express link over a copper cable to the PXIe‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PCIe-8381, x8 Gen2 PCI Express Host, 3.2 GB/s, Copper or Fiber-Optic Cable MXI-Express Device for PXI Remote Control
782361-01
The PCIe‑8381 is an MXI‑Express remote controller for devices or systems cabled over PCI from a computer with a PCI Express slot. The PCIe‑8381 remote controller provides a x8 PCI Express link over a copper or fiber-optic cable to the PXIe‑8380 remote control module when used for PXI system control. Fiber‑optic MXI‑Express solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so industry‐standard desktop computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PCIe-8371, x4 Gen1 PCI Express Host, 832 MB/s, Copper Cable MXI-Express Device for PXI Remote Control
779723-01
The PCIe‑8371 is an MXI‑Express remote controller for devices or systems cabled over PCI from a computer with a PCI Express slot. The PCIe‑8371 remote controller provides a x4 PCI Express link over a copper cable to the PXIe‑8370 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PCIe-8398, x16 Gen3, PCI Express Host, 13.6 GB/s Device for PXI Remote Control
784179-01
The PCIe-8398 is a host interface card used to control a PXI Express chassis over a software-transparent PCI Express Gen 3 x16 link. The PCIe-8398 is installed into a x16 PCI Express slot of a desktop or rackmount PC and is connected to a PXIe-8398 or PXIe-8399 PXI remote control module using Gen 3 x8 copper cables.
-
product
PXI MultiComputing Remote Control Module
PXI MultiComputing Remote Control Modules enable PXI systems to transfer data at multigigabytes per second with only a few microseconds of latency. You can use these models in applications such as real-time tests, hardware-in-the-loop (HIL) tests, and structural tests that need a large number of distributed PXI systems to share data with low latency.
-
product
Remote Controller
ADLINK Bus expansion is a technology that increases the number of slots of the same or different bus type for a host computer system. ADLINK bus expansion product provides variety of interface options, including PCI, PCI Express, PXI, and ExpressCard to increase bus slots and leverage the latest computing power of both desktop and server-grade computers for a variety of applications. The interoperability of different bus interface devices, such PCI, PXI and PCI Express, is also a great benefit for those facing complicated system integration tasks. ADLINK bus expansion products also provide complete hardware and software transparency, without the need for additional drivers or software.
-
product
PCIe Remote Control Interface
51-924-001
The kit is supplied with this PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
product
PCIe Remote Control Interface Card
53-921-001
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules.
-
product
PCI to PXI Remote Control Kit
41-921-001-KIT
This kit provides a seamless connection between a control PC’s PCI interface and a PXI chassis. The PCI to StarFabric module (51-921) resides in one of the controllers PCI slots and provides two independent StarFabric serial interfaces, each capable of driving a separate PXI chassis.
-
product
TB-4304, PXI 96-Pin Female DIN to 82-Pin Female Screw Terminal Block
783870-01
The TB-4304 provides an industrial PXI front-mounting Terminal Block for PXIe-4304 and PXIe-4305 PXI Analog Input Module. It features a 42 V maximum voltage measurement range.
-
product
TB-2676, Ribbon, 100 V, PXI Module Multiplexer Terminal Block
779535-01
Ribbon, 100 V, PXI Module Multiplexer Terminal Block - The TB-2676 features ribbon cable headers that help you access all channels of the PXI-2576 Multiplexer Switch Module. You can use the TB-2676 to configure the 16 banks of 4x1 2-wire multiplexers included with the PXI-2576.
-
product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix Topology Without Column Protection Resistors
782385-07
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix topology With Column Protection Resistors
782385-08
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
NI TB-2644B Terminal Block for NI 2532B as 1-Wire Dual 8x32 Matrix or 2-Wire 8×32 Matrix Topology Without Column Protection Resistors
782385-09
The TB-2644B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 8x32 or 1-wire dual 8x32 matrix. You can directly connect the TB-2644B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2644B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix Topology Without Column Protection Resistors
782385-05
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix topology With Column Protection Resistors
782385-04
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
NI TB-2641B Terminal Block for NI 2532B as 1-Wire 8x64 Matrix Topology Without Column Protection Resistors
782385-03
The TB-2641B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x128 matrix. You can directly connect the TB-2641B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2641B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
product
NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors
782385-06
The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.