Showing results: 151 - 165 of 1364 items found.
-
PRK-130 -
Prostat Corporation
The PRK-130 is an advanced kit that includes the PRF-930 Powder Resistance Fixture for measuring the bulk resistance of powder and granulated materials. Test material is placed in the cavity between the measurement plates. Once a measurement has been made in ohms, a fixture calculation, or correction factor, converts the resistance measurement to volume resistivity in ohm-cm.
-
WTX Series Type II -
ECG KOKUSAI Co., Ltd.
Even 6 lead coil which is not conventionally made by changing the test cable into 6 from 4 is possible. The examination item of DC resistance, impulse, AC hi-pot and insulation resistance can be switched automatically at once.
-
UPLIFT 2000 -
Com-Ten Industries
The Uplift portable tester was designed in conjunction with SPRI, for testing on the field the uplift resistance of adhesion. Easily test the attachment of the tile to underlayment and determine whether the uplift resistance performance meets the minimum wind load requirements.
-
UI-FT02 -
Unuo Instruments
Safety Shoe Impact Tester is to test safety shoe toe cap impact resistance ability. .
-
UI-FT34 -
Unuo Instruments
Zipper Reciprocation Tester is used to test zipper fatigue resistance under lateral and longitudinal tension.
-
-
infraTest Prüftechnik GmbH
For determining the resistance of aggregates against fragmentation in the impact test. The device consists of the safety housing with doors.
-
-
HopeTech
High-stability internal resistance of the battery Meter.The main battery internal resistance and battery voltage. This product can simultaneously measure the resistance and voltage and to compare battery internal resistance and open-circuit voltage.The CHT3560 standard RS232C and HANDLER interface automated measurement fast and accurate judgment the battery deterioration of the situation, sorting products suitable for battery assembly line and factory inspection. Low resistance characteristics can be used to characterize the mechanical and electrical components down low current test conditions.
-
Extech Instruments Corporation
Earth Ground Resistance Tester Kit which includes all hardware necessary to measure earth ground in 3 ranges from 20 to 2000 omega. Also tests AC/DC Voltage, resistance and continuity. Featuring Automatic zero adjustment and three earth ground resistance ranges 20Ω/200Ω/2000Ω. Complete with test leads, 2 auxiliary earth bars, carrying case, protective rubber holster and six 1.5V AA batteries.
-
HH8320 -
Colluck Company Limited
Basic Accuracy 0.5%. 6 Functions / 20 Ranges. Voltage test up to AC750V and DC1000V. Current test up to 10A DC. Resistance test up to 2MΩ. Diode test
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
1863 -
IET Labs
The GenRad 1863 Megohmmeter is the choice for production and inspection tests on devices with resistances up to 20 Tohms. The GenRad 1863 will measure resistance at any of five test voltages of: 50V, 100V, 200V, 250V, and 500 VDC. Compared to the GenRad 1864, which has adjustable test voltages from 10V to 1090V, this unit has fewer controls, and is the more economical of the two models.
-
Torontech Group
Test Chambers are used widely in temperature variation tests, cold resistance tests, and for low-temperature storage in the areas of aerospace and aviation, electronic instruments, electrical products, materials, parts, and components.
-
RMO-M Series -
IBEKO Power AB
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement