Filter Results By:
Products
Applications
Manufacturers
Resistance Test
measured in ohms is the ability of a current to conduct.
See Also: Resistance, Resistivity, Resistance Standards, Resistance Meters, Battery Internal Resistance Testers
-
product
Battery Capacity Analyzer
Model BCA6/12M
- Instant Measurement of energy stored in a storage battery- Tests 6V or 12V Lead Acid Batteries from 2Ah to 100Ah Capacity- Suitable for any SLA, GEL or Car Flooded Batteries- Displays DC Voltage and Balance available Ah capacity of the battery- Shows the Internal Resistance of the battery- Powered by the Battery under test- Micro-processor based digital control of entire testing process- Specially designed 4-terminal probing Battery Clamp of 100A capacity- Test simulates 20-Hr discharge test (C/20) with a few seconds- Bright, back-lit LED Display for test process display- On-screen User Guidance for testing on the built-in LCD Screen- Easy to use, portable and robust housing in a custom extrusion
-
product
High Speed DC Electronic Load
6330A series
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
product
Transformer Winding Resistance Meters
TWA Advanced Series
The TWA advanced series instruments are designed for six-winding resistance measurement and simultaneous three phase on-load tap changer analysis of both the primary and the secondary transformer windings. This is performed with a one singlestep cable setup, with test currents of up to 40A. Each transformer configuration has a special measurement algorithm which is optimized for the fast stabilization of test results. The TWA instruments generate a true DC ripple-free current. Both the injection of the current and the discharge of energy from the magnetic circuit are automatically regulated.
-
product
Transformer Winding Resistance Meters
TWA Standard Series
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
product
LARGE CURRENT 1000A PRIMARY CURRENT INJECTION TEST SET
TEST-901
Beijing GFUVE Electronics Co.,Ltd.
TEST-901 primary current injection test set adopts ARM Chip to control its output process and large capacity of toroidal transformers. It is equipped with LCD display and current meter; it can show primary current value, second current value, turn ratio and the action time. Packing is used as aluminum alloy body with PC panel. TEST-901 is mainly applied to CT turn ratio testing in the power system and contact resistance test which need large current.
-
product
C/I Clamp Meters
CLAMPMETER,OPEN JAW (CSJ-100)
*AC amperage, AC/DC voltage measurement*Open jaw design eases AC current measurement*Slim profile with build-inprobe storage on back*Measures resistance up to 20MΩ*Audible continuity and diode test*Bright LED and audible alarm for non-contact voltage detection*Auto power off for longer battery life*Data hold to capture measurements*2000 count LCD*Accessories included: (2)1.5V AAA batteries, test leads and carrying case*Lifetime Limited Warranty
-
product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Digital Battery & Electrical System Analyzer w/Printer
726
*Accurate Battery & Electrical System Tester *Features programmed test for new Start/Stop Batteries 3 Testers in ONE! 1) 6 & 12 Volt Battery Tester + 12V Start/Stop Battery Test 2) 12 & 24 Volt Charging System Tester 3) Alternator-Starting-Charging System Tester *Wide Testing Range from 40 to 2,000 CCA *Built-in Printer - print the results for permanent service records *Removable/Replaceable Cable Set *Patented Dynamic Resistance Technology
-
product
1000A AC Clamp Meter
CM55
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
product
Auto-Ranging Digital Clamp Meter
DCM401
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
product
Functional & ICT Tester
igentic® 621t
Growing demand for light emitting diode (LED) products and increasing testing complexity continue to challenge electronic printed circuit board (PCB) manufacturers. The igentic® 621t is a flexible PCB tester that ensures quality while increasing production. The tester can handle multiple PCB products and test for light measurements, resistance and push button or post detection, as required.
-
product
Digital Insulation Tester
200M
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT200M is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage from 1 to 30 Volts DC, its short circuit current is less than 100uA. The instrument can measure Resistance from 1 Meg Ohm to 1000 Meg Ohms.
-
product
Flying Probe Tester
FA1817
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
product
Circuit Breaker Contact Resistance Meters
Vanguard Instruments Company, Inc.
The Vanguard Auto-Ohm 10 is a 10-ampere battery powered micro-ohmmeter designed for low-resistance-measuring applications such as the measurement of resistance in circuit breaker contacts, bushing contact joints, and welding joints. The unit is powered by four 3400mAh, 3.7Vdc Li-Ion rechargeable batteries. With these high capacity batteries, up to 2,900 tests per charge (10A/2 second duration) can be performed in the field.
-
product
Digital LOOP/PSC/LOAD Tester
2811 LP
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Displays and sound warning if external voltage present.● Displays mains voltage, scroll trough menus.● Checks wiring integrity (LEDs and display).● Single button operation.● Auto-off/auto-ranging.● Combined prospective short circuit current, PSC and LOOP tester.● Built-in carry case, test leads in separate pouch.● Loop test for L-E and L-N and PSC.● Voltage test L-N and L-E.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for special orders.● 60Hz available on request.
-
product
Low-Temperature Impact Device
DWC-1
This low-temperature impact device is compliance with standard requirement of IEC60245, IEC60227, IEC60540, GB5013-2008, GB5023-2008 and GBT2951-2008. It’s used to test all kinds of PVC sheathed cable, wire, soft wire and no sheath of parallel soft PVC insulated impact resistance at low temperature. Specification: • Working temperature: -15℃±1℃ • Impact height: 10~200mm adjustable • Length of specimen: 5D~150D • Material: 304 stainless steel • Completion time once: 3~5s • Completion number of units for once: ≥2pcs • Weight: 100/200/300/400/500/600/750/1000/1250/1500g • Low temperature box to match additionally
-
product
Salt Spray Chamber
Wewon Environmental Chambers Co, Ltd.
Salt Spray Chamber used for testing the corrosive resistance of products whose the surface was treated with paint, electroplating, inorganic and organic film, anode handling, anti-rust oil, etc. Wall-mount spray system can be freely placed without occupying any effective test space.With imported quartz nozzle, it has the characteristics of smooth interior wall, accurate angle and no crystalline in long-time spraying. Distinctive spring door hinge design makes the chamber door easy to open and close. The inner and external shell of the chamber is made from PVC materials; Easy launder no leakage phenomenon
-
product
AC&DC Digital High Voltage Divider
SGB-C
Wuhan Sangao Electrical Test Installations Limit Co.
high voltage divider1.it is safe and reliable.2.aluminum packing chest as cabinet3.easy to carry and use.high voltage divider, high voltage meter, resistance type high voltage meter, kilo-voltmeterThis series products are general purpose HV measuring instruments ,apply in power system, Electronic Equipment Factory to test frequency AC high voltage and DC high voltage.
-
product
AC&DC Digital High Voltage Divider
SG-SGB
Wuhan Sangao Electrical Test Installations Limit Co.
Specificationshigh voltage divider1.it is safe and reliable.2.aluminum packing chest as cabinet3.easy to carry and use.high voltage divider, high voltage meter, resistance type high voltage meter, kilo-voltmeterThis series products are general purpose HV measuring instruments ,apply in power system, Electronic Equipment Factory to test frequency AC high voltage and DC high voltage.
-
product
True RMS Clamp Meter
DL489
UEi Test & Measurement Instruments
The DL489 True RMS Clamp meter offers contractors better features, functions and safety in a commemorative edition housing. A complete meter with the precision of True RMS and the functionality your job requires. Featuring 600A AC/DC, 750V AC and 1000V DC, resistance, capacitance, diode test, continuity, microamps and LRA Inrush. The DL489 is the complete meter your job requires.
-
product
HV Reed Relays
B-1001-H
*5kV to 15kV Peak Test*3A Continuous*50VA Max Interrupt*NO, NC, DT, Single & Multi-Pole*Safety Encapsulation*HV Leads Available*Compact *Long Life*High Vibration / Shock Resistance*Maximum Creep distance between HV & Actuators Terminals *Tapped base, Turret or Hook terminals, PC Board mounting, Quick disconnect or HV leads available
-
product
Insulation Resistance Meter
AMIC-15k1
*The partial discharge indicator PDI.*Diagnosis of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD*Allows to test the electrical durability of the tested object - indication of breaking voltage.*The high resistance to electromagnetic interference ensures uninterrupted operation in power plants and near high-voltage transmission lines up to 1200 kV AC and 500 kV DC.
-
product
AC Ground Bond Tester
448
Our 448 model is a 4-in-1 tester with 500VA AC Hipot, DC Hipot, Insulation Resistance and Ground Bond testing capabilities. The 448 is capable of a 500VA AC Hipot output to comply with 100mA leakage current test compliance requirements. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application.