Showing results: 151 - 165 of 221 items found.
-
Elrec 6 -
IRIS Instruments
The Elrec 6 is a 6-channel Induced Polarisation (IP) and Resistivity receiver designed to improve productivity when recording deep profiles and soundings. Beside the classical arithmetic and logarithmic modes, ELREC 6 also offers a Cole-Cole mode and ten fully programmable windows for a higher flexibility in the definition of the IP decay curve.
-
PRK-130 -
Prostat Corporation
The PRK-130 is an advanced kit that includes the PRF-930 Powder Resistance Fixture for measuring the bulk resistance of powder and granulated materials. Test material is placed in the cavity between the measurement plates. Once a measurement has been made in ohms, a fixture calculation, or correction factor, converts the resistance measurement to volume resistivity in ohm-cm.
-
Elrec Pro -
IRIS Instruments
The Elrec Pro is a 10 channel Induced Polarisation (IP) and Resistivity receiver designed to improve productivity when recording deep profiles and soundings. Beside the classical arithmetic and logarithmic modes, ELREC Pro also offers a Cole-Cole mode and twenty fully programmable windows for a higher flexibility in the definition of the IP decay curve.
-
Extech Instruments Corporation
Water quality meter can measure thirteen parameters: pH, ORP, temperature, dissolved oxygen, conductivity, total dissolved solids (TDS), salinity, resistivity, specific conductance, ammonium, nitrate, chloride, and barometric pressure.
-
IRIS Instruments
The Elrec Pro Switch is a 10 channel Induced Polarisation (IP) and Resistivity receiver designed to improve productivity when recording deep profiles and soundings. Beside the classical arithmetic and logarithmic modes, ELREC Pro also offers a Cole-Cole mode and twenty fully programmable windows for a higher flexibility in the definition of the IP decay curve.
-
Model FT1 -
Gopal Electronics
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
Static Solutions Inc.
Tests ground for all 110v electrical circuitsWill determine the status of all electrical groundsEasy to use LED lightsWarranteeProduct conforms to the ESD S.20.20 spec standardsIdentify electrical problemsUsed with the Ohm-Stat RT-1000 resistivity meter
-
800 -
ACL Inc.
The ACL 800 Digital Megohmmeter is a dependable and easy-to-use audit kit that is designed to test static dissipative surfaces for electrical resistivity and resistance according to industry standards such as ANSI/ESD test methods S4.1, S7.1, and ASTM D257. Tests are easy to perform with or without the 5lb probes. Use optional concentric ring probe for conformance to STM11.11.
-
GEPS-2000 -
GF Instruments, s.r.o.
Geoelectric Power Sounder GEPS-2000 is a device for data acquisition and interpretation of deep VES (vertical electrical sounding) as well as for 8 channel profiling (resistivity and IP sections). It can be used for measurements up to 1000 – 2000 m depth allowing both high voltage and high current injection of transmitter current according to real measuring conditions.
-
Four Dimensions, Inc.
Our four point probes measure the sheet resistance / resistivity / thickness of a wide variety of materials including group-IV semiconductors, metals, and compound semiconductors, as well as new materials found in flat panel displays and hard disks. We offer a wide range of models, options, and probe heads to suit your materials', measurement, and budget needs.
-
Model 152-1 -
TREK, INC.
The Trek Model 152-1 Surface Resistance Meter is designed to measure surface resistance on a wide varieties of conductive, dissipative, and insulative materials. The Model 152-1 employs a measurement technique which conforms to several ANSI/ESD Association standards for measuring surface resistance and surface resistivity including ANSI/ESD-STM2.1 for garments, STM4.1 for work surfaces, STM7.1 for flooring,
-
IRIS Instruments
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording. The V-FullWaver is a dual channel Induced Polarisation, Resistivity and SP receiver. Continually recording at 10ms sample rate provides a full waveform record. It can be synchronized on the GPS PPS signal, allowing an easy process of the signal. Data on the memory can be downloaded directly on a simple USB stick from all the Fullwavers.
-
STME-RT1000F -
Statclean Technology (S) Pte Ltd
This is a Resistance-Resistivity-Humidity-Temperature Test Kit. It is easy to operate, compact, lightweight, portable meter designed to measure temperature, humidity, and electrical resistance/resistivity. It has both internal and external test probes. The meter will measure resistivity, resistance between two points, and resistance to ground according to EOS/ESDAssociation Standards, -S4.1, S6.1, S7.1, S11.11, and European Standard CECC-EN 1000/15.
-
PDM75-X3 -
Edgetech Instruments
Model PDM75-X3 delivers the Edgetech Instruments Advantage: an ideal system tailored to your application needs. A modular chilled mirror sensor configured to meet your dew point requirements and the chemical resistivity of background gases. Choose the customized sampling system designed to match your process requirements. Select the best user interface options to meet your needs.
-
Delcom Instruments Inc.
Non-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreMeasures nearly all thin conductive materials or coatingsChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterFor benchtop or inline applicationsSimple one-button operationSmall footprint with detached sensor probeOptions include vacuum-ready probe, PC-based productivity software, Ethernet connectivity, stage, and more