Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps)
7-235916000-036
Power, Patchcord, ITA, 36", QuadraPaddle, 16 White Teflon, Single Ended (19 Amps).
-
-
product
RF Power Amplifiers
RF power amplifier category from Pasternack have components packaged in a hermetically-sealed metal enclosures and exhibit outstanding performance in high gain, gain flatness, high linearity and wide dynamic range. RF power amplifiers have excellent performance by using a hybrid microwave integrated circuit design and advanced GaAs pHEMT components. These SMA power amplifier modules are unconditionally stable and include built-in voltage regulation, bias sequencing, and reverse bias protection for added reliability.RF power amplifier over-voltage protection is installed externally for easy repair. These high reliability radio frequency power amps are fully matched internally for 50 Ohm input and output. This 50 Ohm power amplifier matching helps eliminates the need for any additional sensitive external RF tuning components.Our power amps are ideally suited for high linearity applications. These radio frequency power amplifiers offer small signal gain over a temperature range. The Pasternack RF power amplifiers have excellent gain flatness ranges and the IP3 output performance.Most all Pasternack RF power amplifiers are EAR99
-
product
RF Power Amplifiers
Microwave and millimeter wave power amplifiers offer a wide variety of frequency ranges, bandwidths, gain and power outputs. Power amplifiers are used to convert low power signals to high power signals in the device. These are typically used in the Tx chain to amplify the signal before it is sent out via an antenna signal.Example specification in test data will be. Frequency, Small Signal Gain (dB), Output P1dB (dBm), Output Saturated Power, Amplifier Bias, Heat Sink Fan Bias, Maximum RF Input Power.If you are looking for RF Power Amplifiers we have the production capabilities to meet your needs.
-
product
Power Amplifier, RF
Is a type of electronic amplifier that converts a low-power radio-frequency signal into a higher power signal. Typically, RF power amplifers drive the antenna of a transmitter.
-
product
RF POWER AMPLIFIERS
BLWA Series
A) RF-Sample Ports I) 3x 208 V AC / 60 HzB) External Dual Directional Coupler L) LAN Remote ControlC) IEEE-488.2 GPIB Remote Control S) Internal RF Switching UnitD) Front Panel RF Connectors R) RS-232C Remote ControlE) RF Power Indication (digital) U) USB Remote ControlF) Gain Adjustment W) Liquid CoolingH) DC Supply X) External Control of other Amplifiers
-
product
RF POWER AMPLIFIERS
BSA Series
RF Input: N-f, standard on rear panelRF Output: standard on rear panel<1 kW N-f<3 kW 7-16-f<5 kW EIA 1 5/8Mains Supply: Line Power:<1000 VA 100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA 200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA 3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter: via status displayAmbient Temperature: 0 ... +45 °CStorage Temperature: -20 ... +85 °CRelative Humidity: up to 95% (non-condensing)Operating Altitude: up to 2000 m above sea levelVibration and Shock: MIL-STD-810 GCooling: forced air with integral blowerair intake from front, air exhaust at rear
-
product
RF Power Amplifiers
Specially selected products to complement our ultrasound measurement equipment.
-
product
High Power RF Amplifiers
Corry Micronics' line of high power RF amplifiers feature up to 40% efficiency. an extended temperature range of -30 degC to 55 degC for MIL-STD applications, and status monitoring signals that provide diagnostic information.
-
product
RF Power Amplifiers < MMICS
Macom Technology Solutions Holdings Inc.
MACOM is continually enhancing and expanding its MMIC power amplifier product portfolio to meet customers’ demanding technical challenges by leveraging state-of-the-art foundry technologies and proprietary in-house processes. MACOM partners with today’s leaders in Test and Measurement, SATCOM, Aerospace and Defense, Public Safety Radios, Wired Broadband, and Industrial Scientific and Medical applications to deliver industry leading, high-performance MMIC solutions in bare die and high performance packaging.
-
product
RF High Power Broadband Amplifiers
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
product
RF High Power Amplifier Modules
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
product
Solid-State RF amplifier module for High Power Testing
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
-
product
PXIe Dual Channel 20GHz 30dBm RF Amplifier
3202
Model TE3202 is a dual channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PXIe Single Channel 20GHz 30dBm RF Amplifier
3201
Model TE3201 is a single channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
PXI Signal Amplifier
3180
Model 3180 was designed as a general purpose, wide band and high voltage amplifier, however, with specific applications in mind. It offers selectable gain of up to x50, with amplitudes of -90V to +90V and an output current of 150mA.
-
product
PCI Bus Signal Amplifier
3322
Model 3322 is a 3U single-slot, PCI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3322 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
PXI Bus Signal Amplifier
3222
Model 3222 is a 3U single-slot, PXI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3222 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
Wideband Amplifier PXI Card
GX1222
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
product
Signal Amplifier
A10150
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
A10160
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
product
Signal Amplifier
9100
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
Signal Amplifier
9400
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Signal Amplifier
9200A
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Signal Amplifier
9200
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
product
Signal Amplifier
9100A
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
product
Terminal Board for Mitsubishi MR-J3-A Servo Amplifiers
DIN-814M-J3A0
This well-designed motion control terminal board is for the users who use Mitsubishi J3A servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Panasonic MINAS A4 Servo Amplifiers
DIN-814P-A40
This well-designed motion control terminal board is for the users who use Panasonic MINAS A4 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Yaskawa Sigma II Servo Amplifiers
DIN-814PA
This well-designed motion control terminal board is for the users who use Panasonic MINAS A super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8132.
