Showing results: 151 - 165 of 177 items found.
-
IT6900A Series -
I-TECH Electronic Co., Ltd
IT6900A series wide range programmable power supply have built-in standard RS232, USB, GPIB, RS485 and analog interface (RS485 and analog interface are just for IT6900B), support SCPI protocol, facilitate remote control, industrial PLC control and the formation of intelligent test platform. Remote compensation terminals avoid the problem of inaccurate testing caused by voltage drop on the wire.Low ripple, low noise and built-in digital voltmeter make IT6900A easy to do external measurement.IT6900A can be widely applied in DC-DC power supply module, battery charging and sensors and other test areas.
-
BOP Series -
Kepco, Inc.
Kepco's bipolar BOP power supplies are available in 100W, 200W and 400W sizes. For applications requiring higher power, see Kepco's 1KW High Power BOP. For applications requiring higher voltage, Kepco's Series BOP-HV are available in 500V and 1000V models.BOP are high speed power operational amplifiers that can be used to provide dynamically agile voltage for test and simulation. They are not general purpose power supplies. By the nature of the bipolar high speed design, they do not have any energy-storage noise discriminating output capacitors. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
J2110A -
PICOTEST Corp.
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
LQ6324P -
Aplab Limited
- Multi Output Linear DC Power Supply- Digitally Controlled Output Settings- Store / Load 10 Sets of Output Settings in Internal Memory- USB Interface Provided- Programmable Arbitrary Variable Output by Feeding Coefficient of the Curve- User Friendly Front End- Low Cost General Purpose Laboratory Bench Unit- Fully Protected against Overload and Short Circuit- 5V/5A with Over Voltage Crowbar Protection for Digital ICs- Three Independent Outputs Electrically isolated from Each Other- Electrically Floating Outputs up to 500V DC w.r.t. Ground- Precise Regulation, Low Ripple and Noise for Both Constant Voltage & Current Operation
-
IT8912E Series -
I-TECH Electronic Co., Ltd
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Analog Devices Inc.
Analog Devices’ pulse-width modulation (PWM) to voltage output D/A converters convert a PWM input to an accurate, stable, buffered voltage without the ripple, slow settling, and external passive components of discrete filter implementations. Our PWM D/A converters measure the period and pulse width of a PWM input signal and immediately update the D/A converter output with up to 12-bit accuracy and no software coding required. This family of D/A converters is available with 8-bit to 12-bit resolution, dual and quad channels, integrated references, and with high temperature operation. Applications include isolated motor control, automotive headlights or industrial lighting, and other applications that benefit from the simple control interface.
-
SNA5000A -
SIGLENT Technologies
The SIGLENT SNA5000A series of Vector Network Analyzers have a frequency range of 9 kHz to 8.5 GHz, with 2 and 4 port models available. Designed to give you instant insight into scattering, differential, and time-domain measurements. They are effective instrumentation for determining the Q-factor, bandwidth, and insertion loss filters and feature impedance conversion, movement of measurement plane, limit testing, ripple test, fixture simulation, and adapter removal/insertion adjustments. There are five sweep types: Linear-Frequency, Log-Frequency, Power-Sweep, CW-Time, and Segment-Sweep mode. The SNA5000A series VNAs also support scattering-parameter correction of SOLT, SOLR, TRL, Response, and Enhanced Response for increased flexibility in R&D and manufacturing applications.
-
CAEN S.p.A.
- Up to 16 high voltage channels- 15 kV maximum output voltage- Maximum Current 1 mA- CPE, Radial Multipin or Kings connectors- Available with either positive, negative or mixed polarity- Up to 1 nA /100 pA current set / monitor resolution- Up to 200 mV/10 mV voltage set / monitor resolution- Low Ripple, down to < 10 mVpp- 2 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down (1 ÷ 500 V/sec) - TRIP parameter- Current generator operation in over current condition
-
Extech EA33 -
Extech Instruments Corporation
This compact and ruggedly designed meter has a wide measurement range to 99,990 Foot Candles in 5 ranges and 999,990 Lux in 5 ranges with 0.001Fc/0.01Lux resolution. Features include: Store and Recall up to 50 measurements with relative or real time clock stamp, Luminous intensity (candela) calculation, a ripple function that excludes stray light from the primary light source measurement, Multi-point average function, Timed Hold, Relative measurement in absolute value or % deviation, Comparator function with high/low alarms, and Auto Power Off with disable. Complete with built-in stand, light sensor and protective cover with 36” (0.9m) coiled cable, protective holster, 6 AAA batteries, and carrying case.
-
Howland & Lawrence Chamber Services
RF shield testing: IEEE-299, MIL-STD-285, NSA 65-6CTIA CATL certification testing: Probe symmetry and amplitude ripple measurements following Test Plan for Wireless Device Over-the-Air PerformanceAnechoic material test, inspection, remediation: VSWR, inverse spherical nearfield testing of installed material and NRL arch screening tests of individual absorber pieces We can also provide in-process testing of welded steel shielded enclosures with a test technique based on ASME BPVC vacuum box testing—confirm quality of RF welds before the shield envelope is complete. We developed this method for testing the Navy’s Advanced System Integration Lab (ASIL) chamber at Patuxent River, shaving weeks off the construction/testing schedule.
-
CAEN S.p.A.
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 3.5 kV output voltage- Maximum Current 3.5 mA- Either Radiall Multipin or SHV connectors- Available with either positive or negative polarity- Up to 10 nA / 500 pA current set / monitor resolution- Up to 5 mV voltage set / monitor resolution- Very Low ripple, down to < 5 mVpp- 2 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in over current condition- Specific design for High Altitudes 0÷5000 m (A7030 only)
-
G5.BT -
Regatron AG
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
CAEN S.p.A.
- From 12 to 24 independently controllable High Voltage channels- 8 kV maximum output voltage- Maximum Current 1 mA- Either Radiall Multipin or SHV connectors- Available with either positive or negative polarity- Up to 500 pA/50 pA current set / monitor resolution- Up to 100 mV/10 mV voltage set / monitor resolution- Very Low ripple, down to < 5 mV- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Individual Floating (A1534 only)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down (1 ÷ 500 V/sec) - TRIP parameter- Current generator operation in overcurrent condition- Specific design for Germanium detectors (A15x0H only)
-
LXinstruments GmbH
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
CAEN S.p.A.
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 100 V output voltage- Maximum Current: 1mA, 10 mA or 1 mA/100 μA (dual range board)- Individual Enable (A1510 only)- Either DB37, DB25 or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA / 100 pA current set / monitor resolution- Up to 2 / 0.2 mV voltage set / monitor resolution- Extreme Low ripple, down to < 3 mVpp- 3 different channel grounding- Common Ground (AGxxxx)- Common Floating Return (Axxxx)- Full Floating (A1510 only)- Independently programmable for each channel:- Output voltage- Current limit- Ramp up/down- TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A1510)
