Showing results: 61 - 75 of 108 items found.
-
Wuhan Sunma Technology Co., Ltd.
Active Optical Cables, Fiber Optic Transceiver Module is a self-contained component that can both transmit and receive. Usually, it is inserted in devices such as routers or network interface cards which provide one or more transceiver module slot (e.g GBIC, SFP, XFP).
-
ART108 -
Vadatech Inc
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
TI-UPG62 -
TRENDnet, Inc.
4 x Gigabit Ultra PoE ports2 x dedicated SFP slots240 watt power budget12 Gbps switching capacityHardened IP30 rated metal switchIncludes DIN-rail and wall mountsExtreme -40 to 75 ºC (-40 to 167 ºF) operating temperature rangeDual redundant power inputs with overload current protectionAlarm output triggered by power failurePower supply sold separately (TI-S24048)
-
CWDM SFP Transceivers -
M2 Optics, Inc.
CWDM transceiver modules are offered at wavelengths from 1470nm to 1610nm and include LC connectors. These SFPs are 100% compatible with Cisco equipment.
-
10 Gbps SFP+ -
Liverage Corp
Are designed for 10 Gbps serialoptical interfaces for data communications with multimode fiber (MMF).
-
TTEMonitoring Switch, 1 Gbit/s, 12 Ports -
TTTech Computertechnik AG
To complement the existing offering of development products, the TTEMonitoring Switch 1 Gbit/s 12 +1 Ports supports the fast online-mirroring of real-time data streams going through the 12 +1 operational ports of the switch. This switch provides 12 + 1 x 1 Gbit/s full duplex ports which can be equipped with small form-factor pluggable (SFP) modules. Electrical (1000 Base-TX) and optical (1000 Base-SX) SFPs are available.
-
S-110 -
Notice
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
OPTOWARE-S200 (FOTS-Bench Top Series) -
Notice
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
S-120 -
Notice
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
CommFront Communications
Our rugged, industrial-grade, point-to-point Fast and Gigabit Ethernet to fiber optic converters work in pairs to extend 10/100/1000M Ethernet signals over long distance. These Fast and Gigabit Ethernet to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Virginia Panel Corporation
VTAC Wired configurations reduce resistance and increase signal integrity with a seamless transition from wire to connector. This can be demonstrated in an example using the results of VPC quality and performance testing on VTAC patchcords. The results are reflected in the graph below. Insertion loss was tested on one-meter long patchcords with SFP+ terminations on either end. The second data line (red) shows the same patchcord, but bisected and terminated with VTAC connectors in its center. The results show no significant deviation from the SFP signal until approximately 6.25 GHz. Even at 6.25 GHz, there is only -1dB of difference between the two patchcords, which is approximately a 10% loss. With signal integrity playing such an important role in high speed testing, the obvious choices for high bandwidth data testing are VTAC Wired products.
-
Analog Devices Inc.
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
Xtium2 CLHS FX8 -
Teledyne DALSA
Building on the field proven capabilities of Teledyne DALSA’s Xtium™ family of frame grabbers, the Xtium™2 CLHS FX8 features fiber optic cabling for the CameraLink HS interface on the PCI Express™ Gen 3.0 platform. The Xtium2 CLHS FX8 boards feature CLHS X-protocol for high efficiency transmission, support up to four bidirectional SFP+ modules to delivery aggregate bandwidth of 4.8 GBytes/s and can reach cable lengths beyond 100 meters - all in a compact, half-length, single slot solution.
-
cPCI-6S10 -
ADLINK Technology Inc.
*ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch*24-port fully managed Gigabit Ethernet switch*Pre-installed ADLINK PacketManager accelerates packet processing*Layer 2/3 switching with advanced support for VLANs, QoS and IPv6*Two 10 Gigabit Ethernet SFP+ uplink ports*Supports IPMI based on PICMG 2.9 (System Management Specification)
-
Art.-Nr.: TE-1404-1 -
NextGig Systems
The ideal solution for working quickly and efficiently with 1000BASE-T1 EMC measurements The 1000BASE-T1 MediaConverter EMC is especially designed for measurements within the EMC chamber. It is delivered in a Set with an adapter board which enables internal PHY status readings and provides one point-to-point connection between Automotive Gigabit Ethernet and SFP Gigabit Ethernet, with which optical fibre modules are used.