Showing results: 376 - 390 of 477 items found.
-
TT420 -
Electro-Sensors, Inc.
Features • 2-wire, loop-powered 4-20mA analog output • Attachment probe, sensor, and 2-wire 4-20 mA signal conditioner • Compatible with PLCs, meters, and data acquisition systems • No user calibration • TT420Z 1/4" stainless steel probe • TT420S 1/4-28 threaded stud – screws into any 1/4-28 tap • TT420F mounts onto any flat surface • UL listed, Intrinsically Safe (IS) • Class I, (C, D) and Class II, (E, F, G)
-
34000 -
S & G Tool Aid Corp
Test compression on all domestic and foreign cars and most trucks. Adapters fit vehicles with 14mm and 18mm plugs including long reach and 5/8" hex plugs. Flex hose eliminates need to remove auxiliary equipment such as power brakes and steering, air conditioning and manifold. Screw in adapters guarantee accuracy over push-in type testers. Quick side release valve permits retest without removal of adapters. Gage ranges 0-300 PSI and 0-21 BAR. Supplied in storage pouch.
-
784507-01 -
NI
50-Pin Male IDC to 66-Pin Female Screw, Breakout for sbRIO Terminal Block - The sbRIO Breakout Box is a 2 mm insulation-displacement contact (IDC) connector breakout that provides easy access to the multifunction I/O and digital I/O connectors on CompactRIO Single-Board Controllers. The connector breakout provides screw-terminal access to the onboard I/O, which eliminates the need to create a custom cable. You can use this accessory at your desk or mount it directly to the controller for an alternative wiring solution during deployment.
-
34939A -
Keysight Technologies
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
-
BAR-E Series -
Zaber Technologies Inc.
Zaber's BAR-E Series products are computer controlled, motorized, ball screw driven, linear actuators (electric cylinders) with integrated feedback encoders. A built-in encoder allows closed-loop operation and slip/stall recovery features. Each electric cylinder is wired for use with Zaber's A-Series stepper motor controllers, or they can be used with any 2-phase stepper motor controller through the panel mount DB15 connector. When connected to our A-Series controllers, the actuators are designed to be "plug and play" just like all of Zaber's other products.
-
LAR-E Series -
Zaber Technologies Inc.
Zaber's LAR-E Series products are computer controlled, precision lead screw driven, motorized linear actuators (electric cylinders) with integrated feedback encoders. A built-in encoder allows closed-loop operation and slip/stall recovery features. Each electric cylinder is wired for use with Zaber's A-Series stepper motor controllers, or they can be used with any 2-phase stepper motor controller through the panel mount DB15 connector. When connected to our A-Series controllers, the actuators are designed to be "plug and play" just like all of Zaber's other products.
-
Citizen Chiba Precision Co., Ltd.
Miniaturized AC servomotor linear actuators are a type of rectilinear actuator which achieves high precision positioning as well as miniaturization and weight reduction.The motor portion utilizes a hollow AC servomotor, while the encoder portion utilizes a miniaturized and high resolution optical rotary encoder. Since its direct design does not utilize parts such as gears, this makes precise and high resolution positioning possible.In addition to the above characteristics, the MAB and MALB series utilize ball screws that allowed realization of high speed and long service life.
-
T Series -
Thomson
The proven design of the T series precision linear actuators has found its way into thousands of applications throughout the world. Precision-rolled ball screws provide smooth motion, accurate positioning and quiet operation while the slide guide bushings and the rugged exterior design allows it to be used in the thoughest applications. The T series combines durability, performance and ease-of-use with a large selection of factory-engineered options and accessories. Regardless of the environment or requirement, we can customize our standard models to fit just about any application.
-
SparkFun Electronics
The SparkFun MicroMod Teensy Processor leverages the awesome computing power of the NXP iMXRT1062 chip and pairs it with the M.2 MicroMod connector to allow you to plug it into your choice of compatible MicroMod Carrier Board. With the M.2 MicroMod connector, connecting your Teensy Processor is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards). Adding a Teensy to your desired project has never been easier!
-
SparkFun Electronics
The SparkFun RP2040 mikroBUS Development Board is a low-cost, high performance platform with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. Besides the Thing Plus or Feather PTH pin layout, the board also includes a microSD card slot, 16MB (128Mbit) flash memory, a JST single cell battery connector (with a charging circuit and fuel gauge sensor), an addressable WS2812 RGB LED, JTAG PTH pins, four (4-40 screw) mounting holes, our signature Qwiic connectors, and a mikroBUS socket.
-
CSMS-321 -
Power True Systems Corp.
Measuring DCA, DCV, Temperature. 1/32 DIN Size ( 48mmX24mm ). Accuracy: +/- 0.1%(DC), +/- 1%(Thermocouple), +/- 0.2%(Pt100). 3 1/2 Digits Display: 1999. Input Max. 2Adc +/- 10%; 300Vdc, T/C type K: 1200J, Pt100:600J. Aux Power 5Vdc +/- 10%; Isolated Aux. Power 5Vdc, 12Vdc, 24Vdc available in option. Easy to wire, screw type terminal. Outside dimensions is 1/32 DIN Standard ( 48 x 24mm ). High stability & low cost.
-
AD-Series -
Mountz Inc.
The DC control tool is a reliable robotic spindle system engineered for precise, accurate and repeatable torque control. The high performance automation fastening system allows manufacturers to optimize the assembly area, reduce labor costs and increase productivity. The robotic screwdriver system features built-in error-proofing data and screw counter. Multiple fastening strategies can be implemented for sensitive or of difficult assembly joints. Increase productivity as one tool can be programmed to do the job of multiple conventional tools; saving time, maintenance cost, space & training.
-
Mountz Inc.
Faster than hand tools and more precise than air tools, electric screwdrivers are the smart choice for high-volume manufacturers who want to increase productivity. Brushless motors keep your tools on the line by reducing maintenance downtime which, in turn, maximizes your tooling ROI. Mountz electric screwdrivers simplify process control and regulatory compliance by interfacing with screw counters for automatic oversight. You can also meet special manufacturing needs, such as ESD-prevention or clean room requirements, with Mountz's complete lineup of electric tools.
-
ERAVANT
Volume production oscillators utilize either high performance GaAs Gunn diodes with high Q cavity designs or state-of-the-art FET devices with dielectric resonators to yield excellent phase noise and stability. These oscillators are free running with extremely high frequency and power stability. The oscillators are generally designed and manufactured for fixed frequency applications. However, fine frequency adjustments can be achieved by mechanically tuning the provided self-locking screw. While the below standard models are offered for immediate production release, custom models are also available.
-
GBW-600 -
Jinan Testing Equipment IE Corporation
GBW series Erichsen Metal Sheet Testing Machine is designed on the basis of screw universal material testing machine, using the servo motor for highly accurate loading for punching, meanwhile, it is equipped with hydraulic servo control system for pre-tightening/clamping of metal sheet. It is ideal to evaluate the plastic deformation performance and ductility of metal sheet & strip materials. The cupping test for metal sheet thickness range is 0.1mm-5mm, Max. Punching capacity is 600KN, and the pre-tightening/clamping device is with hydraulic servo loading pump for 600kN capacity;
