Showing results: 76 - 90 of 357 items found.
-
605-00007 -
Parallax Inc.
The CO Gas Sensor is used in gas detection equipment for detecting Carbon Monoxide in home, automotive or industrial settings. When paired with our Gas Sensor Board (#27983) it provides a development system and test platform for CO gas sensor design.
-
Alpha Moisture Systems
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
Cohu, Inc.
Cohu‘s well established pressure test equipment are providing high volume final test solutions for all pressure sensor markets.
-
ST05 -
General Technologies Corp.
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
TA-3C -
Tech-Aid Products
The TA-3C test fixture is a combination of the KMD540 testing requirements and the RDR-2000/2100 weather radar interface requirements. This panel allows the technician to test the KMD540 MFD as a stand alone item (with external simulators) or together with a radar sensor for a dynamic real time test. The panel includes the required switching for sensor alignment and KMD testing along with input jacks for the required data inputs. Also built into the fixture is an analog gyro simulator for checking the stabilization functions of the sensor. The full enclosure comes in standard panel width.
-
InHumid Test Module -
Cohu, Inc.
InHumid sensor test system for final test of environmental sensors allows for high volume single-insertion test and calibration of integrated environmental sensors measuring pressure, temperature, humidity and gas.
-
SensorXplorer™ -
Vishay Intertechnology, Inc.
Each sensor board can be used together with the SensorXplorer board.The SensorXplorer boards acts as a USB to I2C interface between Vishay's freely available software modules and the sensor boards. The sensor boards also have test pins for the I2C interface, allowing you to connect them to your own platform.
-
InBaro -
Cohu, Inc.
InBaro MEMS module, a proven solution for accurate barometric sensor test with high throughput and stability.
-
603 -
Sencera Co.
Tilt sensor, 10,000 times on-off lift test. Machinery type, non mercury inside.
-
Astronics Corporation
Our expansive line of Trig-TekTM motion and sensor instruments offers a myriad of test and measurement functionality.
-
Vogelsang & Benning
Series test rig for starter-generator units (ISG)*High voltage test*Insulation resistance measurement*Temperature sensor control*Short circuit test*EMF test*Performance measurement*Manual loading and contacting
-
JYK II -
Kingrun Instrument Co., Ltd.
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
XDK -
Robert Bosch GmbH
Enjoy an all-in-one prototyping platform for sensor based IoT projects. It’s packed with state of the art sensor technology and ready-to-use software packages, capable of fulfilling all your IoT application needs. Start building your project right away to test your idea and validate your concept. Built-in sensors: Accelerometer, Gyroscope, Magnetometer, Inertial measurement unit, Humidity/ Pressure/ Temperature/ sensor, Acoustic noise sensor, Digital light sensor.
-
TU29P -
Matco Tools
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
Data Patterns Pvt. Ltd.
Instrument Test Unit For Advanced Inertial Sensors (INTU) is used for testing and evaluation of Ring Laser Gyro (used in GSLV/PSLV launch vehicles), that detects the angular displacement during rotation. The INTU receives displacement signals from the sensor (RLG) to evaluate the sensor characteristics and also generates signals required towards initiating the action of the sensor.