Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 1681 - 1695 of 2268 products found.

  • One-Component

    LDV System 1 - TSI Inc.

    The pre-configured (typical) one-component (1D) LDV system from TSI gets you up and running in a hurry. The fiberoptic transceiver probe offers point-and-shoot velocity measurement capability with no other probes or sensors needed. The probe is attached to a convenient rotating mount for easy setup. Processing electronics have been pre-selected and configured for a wide range of velocity measurements.

  • Open-source All-in-one Instrumentation

    OpenScope MZ - Digilent Inc.

    OpenScope MZ is a USB/WiFi oscilloscope with a Waveform Generator and Logic Analyzer. What does that mean? It's a device that you connect to your computer (through WiFi or a USB cable) that allows you to acquire, analyze, visualize, and control signals from circuits, sensors, and other electronic devices. Unlike typical USB instruments, OpenScope MZ can also be programmed to run standalone like an Arduino or Raspberry Pi, but with high-speed precision analog and digital I/O.

  • Power Quality Analyser

    PM7000 - Outram Research Ltd (ORL)

    It offers virtually everything needed to monitor and record power for surveys and audits. It includes 4 voltage input channels capable for measuring 0 to 600 Vac and 4 current input channels for use with voltage output current clamps, or Rogowski Coil sensors supplied. Twelve pre-stored connection configurations are set for 3 phase, 2 phase and single phase measurements. Users can also configure their own set-up and math calculation requirements and save them to non-volatile memory.

  • Opto-Isolated Current Loop Signal

    4029 - SPECTEC Innovative Sensor Solutions

    SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.

  • PCI High Density Potentiometer

    50-296-XXX - Digital Communication Technologies Ltd

    The 50-296 is a Programmable Potentiometer module with up to 9-channels of 8-bit resolution potentiometers in a single PCI card. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.

  • PCI High Density Resistor Card

    50-295-XXX - Digital Communication Technologies Ltd

    The 50-295 is a Programmable Resistor module with up to 18-channels of 8-bit resolution resistor chains in a single PCI card. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.

  • Performance Exams

    infraTest Prüftechnik GmbH

    Sturdy sheet steel housing with safety door and electrically driven base with built-on sample mold. The compaction takes place via a rolling segment with force / path-controlled drive device from above. The sample mold and the rolling segment are equipped with software controlled heating. The measurement of force and displacement is done by electronic sensors. The entire compaction process is controlled with Windows software and PC via preselected sequence programs.

  • Personal Chemical Analyzer

    MyDx™ - CDx, Inc.

    Empowering you to live a healthier life by revealing the purity of what you eat, drink and inhale, all in the palm of your hands. MyDx™ allows you test samples of solids, liquids and gases in just 3 simple steps. We have developed four different sensors that will test the organic properties of food, water, air and cannabis.

  • Polarity Indicator Circuit Tester

    CT8007 - General Technologies Corp.

    No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems

  • Electrodes and Probes

    Milwaukee Instruments

    Milwaukee has a wide assortment of pH, ORP, Conductivity and other specialty sensors to meet all your specific requirements. Finding the right electrode for a specific application is a very important task and in order to solve this selection problem it is important to consider the following: electrode body, reference construction and junction. Below you will find a list of Milwaukee electrodes and probes with corresponding instruments they are supplied with. Special electrodes for specific applications can also be manufactured upon request.

  • Device Testing

    Exciter & Stimuli - SPEKTRA Schwingungstechnik und Akustik GmbH Dresden

    SPEKTRA exciter systems cover a wide spectrum of physical stimuli, like translation, rotation, magnet field or pressure to enable stimulated testing and calibration of a large variety of different sensors. Besides a standard-compliant calibration of sensor devices these exciter sytems are also used in complete system level test setups that include stimulus and sensor system testing.

  • Differential Pressure Transmitter

    ABB Series - Xi'an HangSi Mechanical & Electrical Technology Co.,Ltd.

    a differential pressure transmitter with a selectable maximum working pressure of up to 41MPa, 5945psi. It is a reliable sensing system using the very latest digital technologies, providing a large turn down ratio up to 100:1. The user has a comprehensive choice of sensors, as is therefore able to optimize in-use total performance and stability. Configuration is provided via local keys combined with LCD indicator or via hand held terminal or PC configuration platform.

  • Digital Engine Analyzer/Multimeter

    385A - Electronic Specialties Inc.

    The #385A has many of the necessary features required for today’s automotive diagnostics. Use frequency readings to test crankshaft and camshaft sensors, for example. The #385A comes equipped with an RPM pick-up, probe test leads, alligator clip test leads, protective holster, instructions and installed 9V battery. Inductive RPM pick-up features a five position, adjustable sensitivity switch.

  • Digital Gauge Pressure

    ZET 7012-I VER.2 - ZETLAB Company

    ZET 7012-I VER.2 digital gauge pressure (open membrane) is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface. ZET 7012-I VER.2 digital gauge pressure (open membrane) is intended for integration into various technological processes automated control systems. Open membrane type enables sensors operation in viscous, pasty and rapidly polymerizing environments.

  • Digital Gauge Pressure

    ZET 7012-I VER.3 - ZETLAB Company

    Digital gauge pressure ZET 7012-I VER.3 (open membrane) is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface. ZET 7012-I VER3 digital gauge pressure meter is intended for integration into various technological processes automated control systems. Open membrane type enables sensors operation in viscous, pasty and rapidly polymerizing environments.