Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement, Detectors, Meters, Transducers


Showing recent results 1711 - 1725 of 2268 products found.

  • Tide Gauge Recorder

    CEETIDE™ - CEE HydroSystems

    The CEETIDE™ is a simple to install, extremely low maintenance and easy to operate radar tide gauge recorder that can accurately monitor tidal movements in a compact system. There are no moving parts or sensors submerged in water, reducing the amount of maintenance required to maintain an accurate tide gauge installation. The CEETIDE™ can either be permanently installed for port operations or can be used as a portable tide recorder requiring minimal setup.

  • Soil Moisture Sensor

    SoilWatch10 - Pino-Tech

    SoilWatch 10 is a soil moisture sensor which allows measuring relative water content in the soil. Our sensor does not have any exposed electrodes that usually corrode in resistive sensors. Whats more the reads will almost not drift over time or with temperature changes. Our sensor will give the same readings regardless of supply voltage. The sensor is weatherproof. It can be buried in soil for extended periods of time without adverse effects on accuracy or reliability. Designed to work with Arduino.

  • Soil Science and Soil Moisture

    Campbell Scientific, Inc.

    Products for stand-alone soil monitoring. Campbell Scientific instruments are used in a wide variety of soil-science applications. Multiple sensors can be networked in hard-wired or wireless systems to create soil-moisture profiles, while portable, hand-held systems can make point measurements to verify irrigation scheduling or to perform site surveys. Campbell soil sensor products are key to agricultural research, irrigation scheduling, forestry, watershed studies, leak detection, slope stability, and many other disciplines.

  • Soluble Salt Profiler

    130 SSP - Elcometer Limited

    The Elcometer 130 Soluble Salt Profiler provides fast and accurate measurement of the level and density of soluble salts - over 4 times faster than other Bresle equivalent methods. The new Elcometer 130 Soluble Salt Profiler allows you to complete a Bresle equivalent test in just over two minutes. The multi-point conductivity sensors enable the Elcometer 130 SSP to accurately display salt concentration, showing exactly where the contamination lies and generating full colour salt density maps in 2D or 3D.

  • SENSOR FOR THICK & CURVED MATERIALS

    S3 - Delcom Instruments Inc.

    The smallest, simplest, most affordable high-precision non-contact sheet resistance sensor availableNon-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterReads any conductive coatingon even the thickest nonconductive substratesOptions include PC-based productivity software, stage, and morePerformance limited by "lift off" phenomenonelevation of sensor above conductive layer must be carefully controlled

  • Sensor Solutions for IoT

    imec

    Imec is a reference in the design of ultra-low power electronics, low-power algorithms to increase intelligence and data security, and in all aspects of data science. Our multi-sensor environmental monitoring platform features sensors for temperature, relative humidity, NO2, CO2, VOC (volatile organic compounds), particle matter, ambient light, sound, vibrations and presence detection. Our test platform is suitable for indoor and outdoor air quality monitoring and control, and can be used in smart buildings, smart cities and more.

  • Single Channel Signal Conditioner

    SAM-3 - Macintyre Electronic Design Associa

    The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.

  • Single Channel Signal Conditioner

    SAM-3 - Lamar Technologies, LLC

    The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.

  • Single-Channel USB Carrier Demodulator

    CD17 - Validyne Engineering

    The Validyne model CD17 is a USB-powered carrier demodulator for Validyne variable reluctance pressure sensors such as the DP15, DP45 and DP103. The CD17 allows any Validyne variable reluctance sensor to be used directly with a PC via the USB port. Communication and power via USB interface provides remote zero and span adjustment as well as digital pressure readings in mV/V. Drivers and software for the USB interface are included.

  • Single Electrode Dielectric/Conductivity Sensor

    Lambient Technologies

    Suitable for R&D, QA/QC and manufacturing applications with repetitiveoperations, the 8-mm dia. unsheathed and 0.5-inch dia. sheathed single electrode sensorsare designed for use in presses, molds or harsh environments where a tiny, reusabledielectric sensor is desired. They may be mounted so the electrode is flush with a platenor mold surface, insuring no interference with the flow of material during processing.These sensors are constructed with a stainless steel electrode embedded in a hightemperature polymer insulator. An optional thermocouple may be positioned in thesensor cable just behind the sensor head to allow approximate measurement of processtemperatures.

  • SLD Light Source

    FiberLabs Inc.

    The SLD light source is a light source to emit low-coherence light with a broad spectrum like LED and high brightness like LD. Light emitted from a narrow active layer like LD effectively couple to the fiber. SLD light source can be used for optical measurements and sensors, including fiber optic gyroscopes and OCT. FiberLabs provides fiber-output SLD light sources in different wavelength bands from visible to near-infrared light. Our lineup includes bench-top types convenient for experiments and easy-to-integrate module types.

  • Smartphone Seismic Network

    MyShake - UC Berkeley Seismological Laboratory

    MyShake is a free app for Android phones that has the ability to recognize earthquake shaking using the sensors in every smartphone. The app runs “silently” in the background on your phone using very little power – just like the step-tracking fitness apps. When the shaking fits the vibrational profile of an earthquake, the app sends the anonymous information to our central system that confirms the location and magnitude of the quake.

  • Spool Piece Ultrasonic Flowmeter

    FST - Fuji Electric Co., Ltd.

    Three pairs of sensors for accuracy of ±0.2% of rate. Using the new algorithm for calculating the flow velocity, it can measure any type of fluid with high accuracy. Low maintenance. With no moving parts, FST has long-term stability while requiring only minimal maintenance work. Bubble resistant. By using the advanced anti-bubble measurement technology, the interference from air bubbles is greatly eliminated. Pipe diameter: 50 mm, 80 mm, 100 mm.

  • Station Of Acceptance Testing

    ViTec Co. Ltd

    The acceptance test station consists of a personal computer - the workstation of the operator of the testing station, contact mechanisms, as well as current and voltage sensors. The station allows to test up to 10 electric motors of various types simultaneously. The operator of the testing station indicates the test sites at which the engine tests will be conducted, their type (from the database), serial numbers and a set of tests.

  • Steriliser

    S - Memmert GmbH + Co.KG

    The indispensable safety feature for this hot air steriliser: Setpoint Wait. This means that the programme for sterilisation only starts when the set temperature has been reached. This feature can also be used with freely positionable Pt100 temperature sensors. Here the sterilisation time only begins when the set temperature has been reached at all measurement points, and reliable sterilisation is guaranteed at all times.