Filter Results By:

Products

Applications

Manufacturers

Sensors

detect a physical event then translate to a representative analog signal.

See Also: Measurement


Showing results 1741 - 1755 of 2204 products found.

  • Powerful Data Acquisition & Control Software for Powertrain Testing

    iTest - A&D Technology, Inc.

    The iTest system is the central control system in a modern Powertrain test cell. In this function it executes a predefined test schedule by coordinating the dynamometer and throttle systems, along with data acquisition from sensors on the test article or in-cell instruments. iTest achieves this level of functionality through an intuitive configuration editor and user-friendly operator GUI, while employing international standards for connectivity to the test cell instruments. The operator can select from a library of test cycles based on testing standards from North American, European or Asian governing organizations.

  • Programmable Decades

    OCM600 Series - Orbit Controls AG

    OCM600 Series are high accuracy and high stability programmable resistance decades designed as a temperature simulator as well as a programmable resistance decade.In the temperature mode the instrument simulates RTD Sensors within the range from -200 to +850 degree C. Thermometers Pt-100, Pt-200, Pt-500, Pt-1000, Ni-100 and Ni-1000 can be selected. The required temperature value is entered with the keyboard or via the data port. The corresponding resistance is available at 2, 3 or 4 output terminals.

  • Programmable Optical Processors

    WaveShaper Series A - Finisar Corporation

    The new WaveShaper Series A Programmable Optical Processors provide a range of programmable optical filtering and switching options for optical R&D and production test applications.Based on Finisar's high-resolution, solid-state Liquid Crystal on Silicon (LCoS) optical engine, the WaveShaper family provides extremely fine control of filter characteristics, including centerwavelength, bandwidth, shape, dispersion and attenuation. The WaveShaper family is used in a wide variety of applications, including optical communications, pulsed lasers in the medicaland material processing area as well as optical sensors.

  • Programmable Resistor Module

    WF 3144 C-Series - WireFlow AB

    The WF 3144 from WireFlow is a 4-channel, 16 bit, programmable resistor for Compact RIO. The module uses an array of real resistors switched to the desired resistance with solid state relays. Each channel is galvanically isolated, making it ideal for sensor simulation. Application areas Resistive sensor simulation; Pressure sensors, Thermistors, RTDs etc. ATE (Automatic Test Equipment) HiL testing (Hardware in the Loop).

  • PRO Test Lead Kit

    142 - Electronic Specialties Inc.

    #142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.

  • PXIe Optical to 4 port USB 2.0 Hub

    M9407A - Keysight Technologies

    Designed to complement the M9403A and M9404A Optical Link, the M9406A and M9407A is a fully compliant USB 2.0 Hub. The optically extended USB ports enable remote operation and utilize USB devices at the remote end of the optical link. Devices such as USB keyboards, mouse, USB video adapter for a remote monitor can be used for remote control. USB power sensors as well as E-Cal modules can be used to set up measurements. Remote extension of USB devices such as;

  • PXIe Optical to USB 2.0

    M9406A - Keysight Technologies

    Designed to complement the M9403A and M9404A Optical Link, the M9406A and M9407A is a fully compliant USB 2.0 Hub. The optically extended USB ports enable remote operation and utilize USB devices at the remote end of the optical link. Devices such as USB keyboards, mouse, USB video adapter for a remote monitor can be used for remote control. USB power sensors as well as E-Cal modules can be used to set up measurements. Remote extension of USB devices such as;

  • Professional Cordless Circuit Tester

    CT8002 - General Technologies Corp.

    No Ground or clip required. No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance Electronic circuitry. Safety V-groove needle accessory for piercing and carrying. Negligible current draw ( 20 micro-amps) is 10,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 3 and 28 Volt DC in battery powered systems.

  • Preamplifier

    2721 - Georg Fischer Signet

    Pre-amplification is required to protect the output signal of pH and ORP electrodes from a wide variety of electromagnetic interferences common in industrial environments. Signet 2721 is used if remote pre-amplification is required (e.g. tank temperature >80oC) or connecting another manufacturer's electrode to the Signet 5700 or 8750 instrument. The Signet 2721 should be used with special order sensors built with cables (Signet models 277X-HT or 277X-1-HT).

  • PREAMPLIFIERS

    Physical Acoustics Corp.

    Preamplifiers recognize the extremely low amplitude AE signal produced from AE sensors, and convert the signals into amplified and usable forms. As applications and testing conditions vary, project needs may change as well. Physical Acoustics offers an entire line of preamplifiers for a variety of testing requirements. Operating in conjunction with our specialized AE software, preamplifiers also moderate signal size during the data collection process, helping to produce accurate results.

  • Pressure Comparators

    AMETEK Sensors, Test & Calibration

    Our high-pressure, hydraulic pressure comparators are portable, self-contained, hydraulic pressure generators for calibrating pressure gauges, transmitters, sensors, and safety valves. They are much faster than deadweight testers and most automated pressure controllers; and it’s so quick and easy to use, it’s ideal for calibrating those low cost gauges that are often overlooked for ISO9000 compliance. Each pump is available on its own, or in one of our complete ready-to-use pump systems.

  • Power Quality Analyser

    PM7000 - Outram Research Ltd (ORL)

    It offers virtually everything needed to monitor and record power for surveys and audits. It includes 4 voltage input channels capable for measuring 0 to 600 Vac and 4 current input channels for use with voltage output current clamps, or Rogowski Coil sensors supplied. Twelve pre-stored connection configurations are set for 3 phase, 2 phase and single phase measurements. Users can also configure their own set-up and math calculation requirements and save them to non-volatile memory.

  • 13.0 kW and 3.5 kW 13.56 MHz RF Plasma Generators

    SurePower Series - MKS Instruments

    The SurePower® platform of RF plasma generators is the most advanced class of 13.56 MHz generators commercially available. The SurePower® architecture incorporates state-of-the-art RF topologies, patented intrinsic power amplifier protection, improved design margins, and embedded V-I probe sensors to achieve the highest reliability, reproducibility, and accuracy of any generator in the marketplace today.

  • 1-4 Channel Digital Charge Amplifier

    Type 5074A - Kistler Instrument Corp.

    Direct integration of piezoelectric sensors into real time-capable Ethernet systems. Measurement technology for dynamic and quasi-static processes. Open measuring range 20 pC … 1000000 pC. Parameterization via machine control. Up to four piezoelectric signals can be digitized per unit. Individual filtering and scaling of single sensor signals. Individual measurement channel control for asynchronous processes.

  • AC Current Sensor

    RCTi and RCTi 3ph - Powertek LLC

    The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.